the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

561t and xk05 pkt2


Post ReplyPost New Topic
< Prev Topic Next Topic >
new_leaner 
Member - Posts: 14
Member spacespace
Joined: October 31, 2008
Posted: November 07, 2008 at 11:14 AM / IP Logged  

Hi everybody,

I am trying to install 561t RS and XK05(pkt2) to 2002 honda accord with factory alarm, but I don't know how to connect these wires:

-   (H1/3) Yellow Ignition Output to RF system

-   (Brown) Ground when running Input of XK05

thanks for help

chriswallace187 
Gold - Posts: 1,661
Gold spacespace
Joined: March 11, 2002
Location: Pennsylvania, United States
Posted: November 08, 2008 at 11:31 AM / IP Logged  
The yellow ignition wire isn't necessary unless you've got an alarm that's controlling the 561T, in which case it would go to the alarm's Ignition input which would no longer go to the car's ignition wire.
GWR goes to the blue (-) status output from the 561T.
Also PKT2 is the wrong firmware(it's for Toyotas). The correct one is PKH2.
C Renner's Auto Electronix
My service is cheap, quick, and good - pick any two
new_leaner 
Member - Posts: 14
Member spacespace
Joined: October 31, 2008
Posted: November 08, 2008 at 2:37 PM / IP Logged  

thanks a lot, I still have one more question. I read back and forth the installation guide but I don't see any instruction how I can use my current transmitter to start remotely after finish installing 561t. How can I do this ?

thanks again 

chriswallace187 
Gold - Posts: 1,661
Gold spacespace
Joined: March 11, 2002
Location: Pennsylvania, United States
Posted: November 09, 2008 at 2:43 PM / IP Logged  
What were you planning on using to activate the 561T? It's designed to work when it sees the required number of pulses on the WHITE/ red(+) or WHITE/ blue(-) wires.
C Renner's Auto Electronix
My service is cheap, quick, and good - pick any two
new_leaner 
Member - Posts: 14
Member spacespace
Joined: October 31, 2008
Posted: November 09, 2008 at 6:09 PM / IP Logged  
thanks, I am planning to use the door lock to activate the (-) activation input . Is it ok to activate only one activation input or I have to activate both (-) and (+) activation input of 561t in order to make it starts remotely ?
chriswallace187 
Gold - Posts: 1,661
Gold spacespace
Joined: March 11, 2002
Location: Pennsylvania, United States
Posted: November 09, 2008 at 11:39 PM / IP Logged  
You only need to use one of them, but if for some reason you wanted to use both it would be possible.
I see a few problems with this install assuming you're planning on using the factory keyless remote to activate the 561.
1. Honda's OEM keyless entry stops working when the ignition is turned on, so you wouldn't have a way to remotely shut down the car once it was started.
2. Additionally, you wouldn't be able to unlock with the remote for the same reason if the car was running on the remote start.
IIRC the '98-'02 Accords have a separate keyless entry module, and it MAY be possible to cut the ignition wire going to it without interfering with any other vehicle systems...however I don't say that emphatically. Keyless entry module is probably located high behind the passenger side dash.
As far as your activation input you might also use the lock output from that keyless entry module - I believe it's got a conventional (-) wire for that function.
C Renner's Auto Electronix
My service is cheap, quick, and good - pick any two
new_leaner 
Member - Posts: 14
Member spacespace
Joined: October 31, 2008
Posted: November 10, 2008 at 10:44 PM / IP Logged  
thanks to let me know those problem with 561t. I should install a different unit that I can unlock and shut down the car while RS running. Is 562t may be the good one to use ?
chriswallace187 
Gold - Posts: 1,661
Gold spacespace
Joined: March 11, 2002
Location: Pennsylvania, United States
Posted: November 11, 2008 at 12:34 AM / IP Logged  
The problems aren't with the 561T, they're with the Accord. Any aftermarket remote start with keyless entry will resolve them however, including 561R or 562T.
C Renner's Auto Electronix
My service is cheap, quick, and good - pick any two

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Monday, May 13, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer