the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

remote start, ponitac g6


Post ReplyPost New Topic
< Prev Topic Next Topic >
lsondubz 
Copper - Posts: 193
Copper spacespace
Joined: September 20, 2005
Posted: December 01, 2008 at 5:03 PM / IP Logged  
Have a good friend who just picked up a G6, He called and asked me to do a Remote Start/Keyless in it. Ive heard from a few people around there that they are a PITA...Ive been doing Remote Starts for 5-6 Years now but havent actually gotten my hands on any GM 2007+ How are these to do?
racerjames76 
Silver - Posts: 581
Silver spacespace
Joined: November 22, 2008
Location: Ohio, United States
Posted: December 01, 2008 at 8:50 PM / IP Logged  
with the right bypass module, its not bad at all. Most of the connections are in the passenger side of the center console. Ignition switch wires a lil tight but not impossible. Hope that helps!
lsondubz 
Copper - Posts: 193
Copper spacespace
Joined: September 20, 2005
Posted: December 05, 2008 at 9:29 PM / IP Logged  
I get all my stuff from bypasskits...Ive never done one so I was lookin for some advice
lsondubz 
Copper - Posts: 193
Copper spacespace
Joined: September 20, 2005
Posted: December 09, 2008 at 3:53 PM / IP Logged  
It looks like I only need to use the XK06 with PKG7 Firmware?? Do I need to do anything special for the start sequence to work properly? Im using and Audiovox APS-57 which I believe does drop the ACC wire during crank so it should automatically work right? I want to do this asap if I can so please any help would be appreciated
racerjames76 
Silver - Posts: 581
Silver spacespace
Joined: November 22, 2008
Location: Ohio, United States
Posted: December 09, 2008 at 4:13 PM / IP Logged  
IMPORTANT: There is no need to connect
the accessory output wire from the remote
starter to vehicle. The PKG7 will take care
of this function.
according to the manual which it does look like you have the right bypass, you dont need the accessory wire.
lsondubz 
Copper - Posts: 193
Copper spacespace
Joined: September 20, 2005
Posted: December 10, 2008 at 11:12 AM / IP Logged  
So Id only need to wire the Ignition wire to the car, will the Acc still power up once the start sequence is finished?
racerjames76 
Silver - Posts: 581
Silver spacespace
Joined: November 22, 2008
Location: Ohio, United States
Posted: December 10, 2008 at 5:48 PM / IP Logged  
correct just follow the install guide remote start, ponitac g6 -- posted image.
Mike M2 
Platinum - Posts: 2,652
Platinum spacespace
Joined: June 29, 2005
Location: United States
Posted: December 10, 2008 at 6:39 PM / IP Logged  
I am not a fan of XK bypasses. Do a search here and you will see a thousand threads of issues guys here are having getting them programmed. I have done a few G6's using the Idatalink bypass and it seems to work flawlessly, plus it will do a lot more for you like give locks, door and trunk triggers, trunk release, RAP shutdown, even a tach wire.
Mike M2
Tech Manager
CS Dealer Services
NowYaKnow 
Gold - Posts: 1,216
Gold spacespace
Joined: December 18, 2002
Posted: December 10, 2008 at 9:42 PM / IP Logged  
"Do a search here and you will see a thousand threads of issues guys here are having getting them programmed."
To be fair they have been around a lot longer as well. iData will have their thousand threads as well in time..
For the original poster this is a very simple vehicle. Go with the XK06 PKG7 and you'll be golden. Don't waste your time at the pass side of the center console either. Grab everything in the main harness in the drivers kick panel. The only thing you run anywhere else is the ignition wire and the bypass wiring. Well hood and tach if you feel like hooking those up. Good luck.
lsondubz 
Copper - Posts: 193
Copper spacespace
Joined: September 20, 2005
Posted: December 12, 2008 at 2:10 PM / IP Logged  
Well I use all Bypasskits units and have yet to have any issues with them, some of them are harder to program but it just takes and extra few mins til its right...I have both the XK06 and the PKUGM2X which is the transponder bypass as well...Im assuming the XK06 is probably a little easier, so just wire the bypass no need for ACC and only IGN to the ignition harness? Sounds like its a little easier than I thought

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Sunday, August 14, 2022 • Copyright © 1999-2022 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer