05 f350 remote start wiring

Home / the12volt's Install Bay / Car Security and Convenience / 05 f350 remote start wiring (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

montaruli

Member - Posts: 2

Joined: December 29, 2008

Location: Alberta, Canada

Posted: December 29, 2008 at 2:24 PM / IP Logged

I have searched this site and Found the Direct Wire Sheet for my Ford F-350 this is what I have done so far, and the truck won't crank. If someone could point me in the right direction, it would be greatly apppreciated.

Below is a link for the wiring Schematic from AUTOSTART.

Thanks in advance for any help!

This is the mess I have so far lol.

Color at Starter Purpose Color at truck

Yellow Ignition wire RED / LtGreen

Red 12V Yellow

Orange Access Gray / YELLOW

Purple Starter Dark Green

Green 5th Relay ????

Red 12V LTGREEN/ Purple

Black Ground Frame

Purple Tach AC GREEN / WHITE

Grey hood switch Hood Switch

Orange Brake switch N/A I had it hooked to the brake pedal wire but then cut it as I read closer and it said only to connect for Man trans.

Yellow Parking Lights N/A couldn't find that wire

And I have the antenna hooked up

This is the wiring Diagram from Autostart

https://i40.photobucket.com/albums/e244/montaruli/wiring1.jpg

moonliter

Copper - Posts: 322

Joined: February 28, 2007

Location: Canada

Posted: December 29, 2008 at 2:56 PM / IP Logged

Ok, I can see what you were missing. You need to connect ignition 2 ( which should be RED / black in the truck ), use the 5th relay green wire from your rs. Make sure the jumper at the back of the brain is sitting in the middle slot.

Don't confuse the brake switch with the parking brake switch. You need to reconnect the orange wire to the brake pedal switch. It should show 12 volt when the brake pedal is pressed. This brake switch is essential, you need it to shut down the remote start as well as for programming the brain.

Before you can remote start, you need to program the tach. You didn't mention what model is your rs. On newer module, you will need to cut the yellow loop for automatic transmission.

moonliter

Copper - Posts: 322

Joined: February 28, 2007

Location: Canada

Posted: December 29, 2008 at 3:19 PM / IP Logged

The brown parking light wire (+) is located at the back of the headlight switch. You can remove the headlight switch from the dash to access it.

montaruli

Member - Posts: 2

Joined: December 29, 2008

Location: Alberta, Canada

Posted: December 29, 2008 at 6:40 PM / IP Logged

The model is GS-2260TW-FM

And thanks I misread the instructions about the brake wire. The is one wire which just says brake, and the other says parking brake, I'll switch it to just the first brake wire.

I had no clue what 5th Relay meant. On my Directwire sheet I had 3 accessories wires but only one on my RS. The Igntion 2 (BLACK/ Red) is listed as an accessory. I will hook it up to the Green 5th relay tomorrow and see what happens.

There is also a Drk. Blue/Lt Green wire that is listed as Second Accessory does this hook up to anything?

Never even thought to get the parking lights right at the switch, my schematic said N/A for parking lights.

Thanks again, I will hook these wires up tomorrow and update.

moonliter

Copper - Posts: 322

Joined: February 28, 2007

Location: Canada

Posted: December 29, 2008 at 8:22 PM / IP Logged

Yes, you are right, this truck has 1 ign & 3 acc wires.

This is what I got for the F350 HD 5.4L gas engine wiring at the main ignition harness

+12 volt -- Yel & grn/pur

Ign -- RED / grn

Acc#1 -- RED / blk

Acc#2 -- gry/yel

Acc#3 -- dk.blu/lt.grn

Start -- dk.grn

Ok, you still need to use the green wire (5th relay) connected to RED / blk (acc #1)

this output is programmable, it can be used as an ign #2 or acc #2 or starter #2

by placing the jumper in the appropriate slot at the back of the module. see the diagram you attached.

Since you already used the orange wire for gry/yel (acc #2), then you need an extra bosch relay

to connect to the dk.blu/lt.grn (acc #3)

pin 86 to orange from the rs,

pin 85 to the ground when running ( pin 10 white wire from rs )

pin 87 to constant 12 volt (yel)

pin 30 to dk.blu/lt.grn (acc #3) in the truck

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

05 f350 remote start wiring

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.