the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2008 dodge ram 1500 qc remote start


Post ReplyPost New Topic
< Prev Topic Next Topic >
jburbano 
Member - Posts: 20
Member spacespace
Joined: June 29, 2005
Location: United States
Posted: July 16, 2009 at 9:45 PM / IP Logged  

I posted this over a year ago.

"I am looking for some details on how to add to the existing factory alarm in a 2008 Dodge Ram 1500 QC.  This truck has the factory alarm and integrated key/remote.  I would like to add remote start and additional sensors to the alarm or replace it.  DEI sems to have the necessary interface but I am unsure which to use or if they will allow me to add remote start AND additional alarm sensors."

I had a couple of replies that seemed overly complicated.  So I waited hoping for better options.  It looks like their are some new modules that allow you to integrate directly into the harness and do not require permanent use of a spare key.  I want something that will allow remote start with automatic timeout and that will allow me to start the engine while leaving the doors locked (until I unlock them), and the alarm on.

Has anyone found something like this?  Can you comment on all the parts that were required and how difficult the install was?

Thanks!

profuse007 
Gold - Posts: 2,015
Gold spacespace
Joined: October 20, 2002
Location: Texas, United States
Posted: July 17, 2009 at 1:42 PM / IP Logged  
just like any RS add-on, you trigger the RS through your lock wire. after that your remote becomes dead, that can be annoying after owning it. also you will need an immobilizer bypass unit for RS to even work.
here's the bad part, 6mos from when you got it installed, you'll want a stand-alone RS system bc you lost keyless entry.
remote start systems are fairly cheap these day. you can probably find a complete unit for about 50bucks, made by DEI.
Houston,TX
"The two most common elements in the universe are H+ and stupidity" (Ellison).
jburbano 
Member - Posts: 20
Member spacespace
Joined: June 29, 2005
Location: United States
Posted: July 17, 2009 at 2:22 PM / IP Logged  

Sounds like exactly what I am trying to avoid!! 

I put an Omega alarm/remote start system in my old truck that did exactly what I want now. Remote start *AND* independant alarm control.  So I could start my truck with the alarm turned on and doors locked.  Then unlock the car, get in, put the key in (just to on position), drive away.  If you opened the door w/o using the remote unlock, the alarm would sound and the engine would stop.  After a remote start, the preset period (you set it) would eventually expire and the engine would turn off automatically.

The Omega system was not expensive and had a lifetime warranty. But it was completely hardwired and required a key for the bypass. Quite an involved install.  If they had the same one for my newer RAM that used the computer bus interface (instead of all of the hard wiring), and required no dedicated key.  I would buy it!

It is really hard for me to tell how these new systems work and how many Extra pieces you need to complete the install!  

racing_bidule 
Copper - Posts: 66
Copper spacespace
Joined: December 13, 2007
Location: Quebec, Canada
Posted: July 20, 2009 at 1:26 AM / IP Logged  

Hi, you can use the vehicle databus to control the doorlocks and alarm and also pickup many signals from the vehicle network as tach, doorpins, glow plug status.

In your vehicle a CAN module will be required to avoid hardwiring.

One of the modules you can use is the iDatalink ADS-AL CA (can fit any r.s.) or BLADE ALL with a Compustar.

Both products will be available through a professional install shop. The products should be installed by professionals since any bad alteration of your CAN network can affect the entire vehicle functionalities.

Regards!

If you fail on your first attempt, at least destroy all evidence you tried!
jburbano 
Member - Posts: 20
Member spacespace
Joined: June 29, 2005
Location: United States
Posted: July 20, 2009 at 8:10 PM / IP Logged  

Thanks for the reply.  Unfortunately, I am not looking for an install shop. 

I am hoping someone will share first hand personal experience with this install and that they will share complete details of what it took to get the job done.

The products you suggested are probably good options but it seems they are incomplete by themselves. 

I have seen numerous posts with partial solutions that really don't help. Has anyone been able to install a system in the 08 RAM 1500 with the capabilities I described earlier?  If so, PLEASE chime in with details!   It would be greatly apreciated!


Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Monday, December 6, 2021 • Copyright © 1999-2021 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer