viper 5701, where do i start

Home / the12volt's Install Bay / Car Security and Convenience / viper 5701, where do i start (

Topic Closed)

Welcome Guest :)

Members

< Prev Page Next Page > < Prev Topic Next Topic >

howie ll

Pot Metal - Posts: 16,466

Joined: January 09, 2007

Location: United Kingdom

Posted: December 21, 2009 at 12:58 PM / IP Logged

Isn't this another please read my post "Rookies seeking advice".

Basic job minimum

A reasonable DMM

Ratchet Crimpers

Side Cutters

Strippers

Stanley Knife (Non retractable blade)

Soldering tool

60/40 Flux cored solder

Heat shrink sleeving, 3.2mm (1/8") 6.4mm (1/4") and 9.6mm (3/8")

Good tape such as Scotch 33+

Cordless drill screwdriver with bit assortment and 4-14mm (5/16"-1/2")stepped cone cutter

Sockets, either 1/4" or 3/8" drive, 7,8,10,12, and 13mm only metric

Sundries, relays, diodes various crimp connectors.

KPierson

Platinum - Posts: 3,527

This member consistently provides reliable information

Joined: April 14, 2005

Location: Ohio, United States

Posted: December 21, 2009 at 1:59 PM / IP Logged

The only products you "need" are the alarm/remote start and the security bypass. You do NOT need a battery backup or any other sensors. Again, concentrate on just getting the thing installed and working before you complicate the situation by adding accessories.

Kevin Pierson

djbdub

Member - Posts: 25

Joined: December 20, 2009

Location: Ohio, United States

Posted: December 21, 2009 at 3:38 PM / IP Logged

ok, toolz...check. viper 5701 alarm/remote start..havent ordered it yet. for the security bypass, would a GM Data Immobilizer Bypass work?? if not, what GM bypass works? as for the Sundries, relays, diodes various crimp connectors, where about can i pick some up ad how many would i use..???

Thank You All...

05gt

Silver - Posts: 628

Joined: October 30, 2005

Location: British Columbia, Canada

Posted: December 21, 2009 at 4:24 PM / IP Logged

For the bypass module get the idatalink ads-al-ca, you will need this one because it is the only module for chevy that you can flash with the DBI firmware

like what was mentioned above, stick to geting the essentials working first, worry about the tilt sensor and backup battery last

to be honest with some of these questions I would really consider taking it to a shop to get this done, you don't want a costly trip to the dealer

howie ll

Pot Metal - Posts: 16,466

Joined: January 09, 2007

Location: United Kingdom

Posted: December 21, 2009 at 4:32 PM / IP Logged

Sorry Ted, I'm with Kevin on this one, I'm also very much with 05gt, you will save yourself an awful lot of trouble taking it to a pro, but if you want to go ahead, be my guest WEhave no legal liabilities here.

Again I suggest leaving the sensor(s) to last in fact the 507m requires careful setting up, you'll probably have to change it's position at least once,I'd recommend a 508d dual zone prox instead. You will need the diodes for the locks, 1N4004 from radio shack unless the by-pass handles that. I can see this is going to be the biggest transatlantic co-operation effort since Gulf War ll

howie ll

Pot Metal - Posts: 16,466

Joined: January 09, 2007

Location: United Kingdom

Posted: December 21, 2009 at 4:37 PM / IP Logged

Have you even looked at the wiring guide to this vehicle in the vehicle wiring section?

05gt

Silver - Posts: 628

Joined: October 30, 2005

Location: British Columbia, Canada

Posted: December 21, 2009 at 8:34 PM / IP Logged

howie

the idatalink modules does doorlocks for him, thats one less thing he has to worry about, lol

djbdub

Member - Posts: 25

Joined: December 20, 2009

Location: Ohio, United States

Posted: December 21, 2009 at 10:57 PM / IP Logged

ok..

Viper 5701 alarm/remote start..

Toolz..

idataLink ADS-AL CA .. & a, iDatalink OmegaLink adsusb Weblink Updater Computer Cable...

any relays needed? if so what kind, n what for/how many???

diodes?? how many/what for?? what kind??

Thank You All...

05gt

Silver - Posts: 628

Joined: October 30, 2005

Location: British Columbia, Canada

Posted: December 21, 2009 at 11:03 PM / IP Logged

you will need 1 relay, this will be used to power the 2nd accessory wire in the vehicle

you will need 2 diodes, these will be ised for the 2 rear doors as the idatalink module will not cover these

djbdub

Member - Posts: 25

Joined: December 20, 2009

Location: Ohio, United States

Posted: December 21, 2009 at 11:11 PM / IP Logged

1 relay......where do i go about getting the right one, do you have a link, to point me to the corect one???

as for the 2 diodes for the rear windows, can i get those at radio shack? if so What kind should i use for the rear windows for this 04 tb??

Thank You All..

< Prev Page Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.