the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

nitro bmwx 433 alarm/starter on 99 legacy

Home / the12volt's Install Bay / Car Security and Convenience / nitro bmwx 433 alarm/starter on 99 legacy (Topic Closed Topic Closed)
Welcome Guest :)

Post ReplyPost New Topic
< Prev Topic Next Topic >
kreg357 
Platinum - Posts: 7,789
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: January 30, 2009
Location: Pennsylvania, United States
Posted: May 28, 2011 at 9:17 AM / IP Logged  

The Neutral Safety Input : Is your Legacy an Automatic or Manual Transmission vehicle?

If you have an Automatic :

Verify that your car will not crank when in any gear selection other than Park or Neutral.  If that test passes then connect the Neutral Safety wire to the Parking Brake switch. This switch is found at the Parking Brake and the correct wire goes to gound when the Parking Brake is engaged.

Soldering is fun!
shawnwiosna 
Member - Posts: 14
Member spacespace
Joined: May 27, 2011
Location: New York, United States
Posted: May 28, 2011 at 9:27 AM / IP Logged  
can you help me find the red and white door trigger wire. Is it the wire coming from the pin in the door
SimmpleeDaBesst
kreg357 
Platinum - Posts: 7,789
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: January 30, 2009
Location: Pennsylvania, United States
Posted: May 28, 2011 at 9:43 AM / IP Logged  

The easiest place to find / connect is at the Keyless Lock module.  That was the top picture in the prior post with the Lock, Unlock and Horn wires marked.  Look for the RED / White door trigger and the Yellow/Black Trunk trigger wires there.  Use your Digital Multi Meter to verify you found the correct wires.

DMM setup for (-) Trigger wires:

DMM set to 20V DC.   Red lead to +12v constant.  Black lead to suspect wire.  DMM should go to +12v when any door is opened.

Soldering is fun!
shawnwiosna 
Member - Posts: 14
Member spacespace
Joined: May 27, 2011
Location: New York, United States
Posted: May 28, 2011 at 9:46 AM / IP Logged  
got the keyless entry to work. Yeahh.. I forgot to hook the ground wires up
SimmpleeDaBesst
kreg357 
Platinum - Posts: 7,789
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: January 30, 2009
Location: Pennsylvania, United States
Posted: May 28, 2011 at 9:58 AM / IP Logged  
Yes, the install guide does not highlight those two relay input wire connections to ground for the Type B (-) lock wiring.   I had to look closely to see the difference between Type A (+) and Type B (-)..............      nitro bmwx 433 alarm/starter on 99 legacy - Page 2 -- posted image.
Soldering is fun!
shawnwiosna 
Member - Posts: 14
Member spacespace
Joined: May 27, 2011
Location: New York, United States
Posted: May 28, 2011 at 10:02 AM / IP Logged  
does the remote starter harness work on the same principle that the ground input wires for ex. Neutral safety and wait to start diesal HAVE to b connected
SimmpleeDaBesst
shawnwiosna 
Member - Posts: 14
Member spacespace
Joined: May 27, 2011
Location: New York, United States
Posted: May 28, 2011 at 10:05 AM / IP Logged  
my car is automatic and NOT diesal by the way
SimmpleeDaBesst
kreg357 
Platinum - Posts: 7,789
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: January 30, 2009
Location: Pennsylvania, United States
Posted: May 28, 2011 at 10:09 AM / IP Logged  

Neutral Safety has to be connected.  Other important safety wires that must be connected are the Brake (+) and the Hood Pin switch.

Diesel Wait to Start is only used on diesel engines.

Soldering is fun!
shawnwiosna 
Member - Posts: 14
Member spacespace
Joined: May 27, 2011
Location: New York, United States
Posted: May 28, 2011 at 10:27 AM / IP Logged  
got the starter function to work. Last thing is the door and trunk triggers which I am still stumped on
SimmpleeDaBesst
shawnwiosna 
Member - Posts: 14
Member spacespace
Joined: May 27, 2011
Location: New York, United States
Posted: May 28, 2011 at 10:29 AM / IP Logged  
I cannot find the damn red and white wire
SimmpleeDaBesst
Page of 3

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Wednesday, May 22, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved • Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer