cannot enter program mode

Home / the12volt's Install Bay / Car Security and Convenience / cannot enter program mode (

Topic Closed)

Welcome Guest :)

Members

< Prev Page < Prev Topic Next Topic >

roger555

Copper - Posts: 76

Joined: July 24, 2009

Location: North Carolina, United States

Posted: September 11, 2011 at 8:54 PM / IP Logged

Thanks anyways hopefully someone can chime in or else might just buy a bitwiriter and try that I was thinking about getting one anyways. Maybe its locked out somehow

jmsounds

Copper - Posts: 99

Joined: June 28, 2007

Location: Maryland, United States

Posted: September 12, 2011 at 11:38 AM / IP Logged

hello i think you are not holding the valet switch too long

you have to wait until it gives you the 3 crirps you may have

to hold it for a at least 5 to 10 seconds

ok good luck

roger555

Copper - Posts: 76

Joined: July 24, 2009

Location: North Carolina, United States

Posted: September 12, 2011 at 6:54 PM / IP Logged

Like I said I can hold it for a minute and all it does is go into valet mode once I release the button. It might not solve the problem but I ordered a bitwritter. I was going to order anyways so hopefully I can program it that way.

buddholly

Copper - Posts: 244

Joined: August 24, 2006

Location: United States

Posted: September 13, 2011 at 2:33 PM / IP Logged

Leave the ignition turned on. Shouldn't turn the ignition off until you have changed your programming options.

roger555

Copper - Posts: 76

Joined: July 24, 2009

Location: North Carolina, United States

Posted: September 13, 2011 at 3:30 PM / IP Logged

I have tried with the key still in and turned to ignition I'm pretty sure. I'll try again wheh I get home but I thought the instructions say turn on then off and hold the program button.?

buddholly

Copper - Posts: 244

Joined: August 24, 2006

Location: United States

Posted: September 13, 2011 at 4:21 PM / IP Logged

^Nope. That's only to enter valet mode. You need to have the ignition on to due any other programming, the last step is to shut the ingition off.

clarence1996

Member - Posts: 15

Joined: March 17, 2007

Location: Louisiana, United States

Posted: September 13, 2011 at 5:15 PM / IP Logged

Run green to a ground and you can do it.

TheWire1

roger555

Copper - Posts: 76

Joined: July 24, 2009

Location: North Carolina, United States

Posted: September 13, 2011 at 5:47 PM / IP Logged

I guess the wording on the instructions is wrong, I'm headed out to give it a try!

P.S. Clarence I said in my first post I am grounding the green wire already

cannot enter program mode - Page 2 - Last Post -- posted image.

roger555

Copper - Posts: 76

Joined: July 24, 2009

Location: North Carolina, United States

Posted: September 14, 2011 at 4:55 PM / IP Logged

Well thanks everyone I hate to admit it but I figured out the problem, when I was prepping the wiring and the molex connectors I must of somehow switched the Green & violet wire locations on the molex so I wasn't actually grounding out the green wire! Doh!

< Prev Page

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

cannot enter program mode

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.