the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

honda vtx 1800n brake line relay


Post ReplyPost New Topic
< Prev Topic Next Topic >
ssathre 
Member - Posts: 5
Member spacespace
Joined: June 10, 2012
Posted: June 10, 2012 at 11:29 PM / IP Logged  
im installing a automatic turn signal cancelation device on my bike, it's called a signal minder. it replaces the stock turn signal relay and will turn off the indicators after a pre set amount of time. one feature is if you hook up your brake light wire it will pause the timer when it senses the 12 volts from the brake light.
my problem is that my bike runs a continuous 6 volts (for the running lights) until the brake is applied then it ups the voltage to 12volts. this 6 volts has a negative effect on the singnalminder.
is there a way I can have a relay that splits off the normal brake wire that would tie into the signalminder. when it senses the jump to 12 volts it would send a 12 volt supply to the signalminder?
oldspark 
Gold - Posts: 4,913
Gold spacespace
Joined: November 03, 2008
Location: Australia
Posted: June 11, 2012 at 12:37 AM / IP Logged  
Take the signal from the brake switch(es) instead of the lights.
If it's a grounding switch, use a relay to invert the signal.
There are other options, but find out what minimum voltage is needed to halt the timer.
i am an idiot 
Platinum - Posts: 13,692
Platinum spaceThis member consistently provides reliable informationspace
Joined: September 21, 2006
Location: Louisiana, United States
Posted: June 11, 2012 at 8:37 AM / IP Logged  
Follow the wire from the brake light to the module under the seat. At that module you should find the wires from each of the brake switches. You should get both of those wires.
Are you sure it is not a dual filament bulb?
i am an idiot 
Platinum - Posts: 13,692
Platinum spaceThis member consistently provides reliable informationspace
Joined: September 21, 2006
Location: Louisiana, United States
Posted: June 11, 2012 at 8:55 AM / IP Logged  
According to the Microfiche at buymotorcycleparts.com, there are 3 wires going to the Brake/Tail assembly. One should be for running lamps and the other will be for brake. There is also a separate set of wires for the license plate lamp.
ssathre 
Member - Posts: 5
Member spacespace
Joined: June 10, 2012
Posted: June 11, 2012 at 9:59 AM / IP Logged  
Thanks, Olspark! that makes it all the more simple!
ssathre 
Member - Posts: 5
Member spacespace
Joined: June 10, 2012
Posted: June 11, 2012 at 10:00 AM / IP Logged  
i am an idiot wrote:
According to the Microfiche at buymotorcycleparts.com, there are 3 wires going to the Brake/Tail assembly. One should be for running lamps and the other will be for brake. There is also a separate set of wires for the license plate lamp.
I have the N model. It has a continuous 6 volts until the brake level is applied then it ups it to 12.
Thanks.
i am an idiot 
Platinum - Posts: 13,692
Platinum spaceThis member consistently provides reliable informationspace
Joined: September 21, 2006
Location: Louisiana, United States
Posted: June 11, 2012 at 12:55 PM / IP Logged  
The fiche I viewed was for the 08 N3. What year is your bike? Are there 2 separate harnesses going into the taillight area? One for License plate lamp and the other going into the brake/tail? Are there 3 wires on the brake/tail harness?
ssathre 
Member - Posts: 5
Member spacespace
Joined: June 10, 2012
Posted: June 11, 2012 at 1:07 PM / IP Logged  
i am an idiot wrote:
The fiche I viewed was for the 08 N3. What year is your bike? Are there 2 separate harnesses going into the taillight area? One for License plate lamp and the other going into the brake/tail? Are there 3 wires on the brake/tail harness?
I have an 08 vtx1800n spec1. There are 3 wires going to the brake/tail harness.
i am an idiot 
Platinum - Posts: 13,692
Platinum spaceThis member consistently provides reliable informationspace
Joined: September 21, 2006
Location: Louisiana, United States
Posted: June 11, 2012 at 3:06 PM / IP Logged  
How many of the wires have 6 volts on them?
ssathre 
Member - Posts: 5
Member spacespace
Joined: June 10, 2012
Posted: June 12, 2012 at 8:08 AM / IP Logged  
i am an idiot wrote:
How many of the wires have 6 volts on them?
only one, the green and yellow... which is the brake (@ 12 volts) and running light @ 6 volts

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Sunday, October 6, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer