heater does not come on after remote start

hello, just bought a viper 5904V installed everything including remote start but some how my heater on my 1991 toyota celica does not come on once you take the key off the ignition. need help how to make this work thank you

On the ignition switch harness from the car you will find a Grey wire this is your Accessory wire that controls the heater and other stuff , this wire needs to be connected to the Orange wire from the Alarm"s ignition harness.triniforever

Probably a good idea to post what wires from the alarm you connected to what wires in the car!&triniforever

Remote Start, 10-pin heavy gauge connector Alarm Harness        Description Car Harness Pink + ignition 1 input/output BLACK/ Orange RED / White + fused (30A) ignition 2/flex relay input 87    constant Orange+ accessory output    grey Violet     + starter output car side of the starter kill blk/wht Green      + starter input key side of the starter kill   blk/wht Red        + fused 30A ignition 1 input    constant Pink/White + ignition 2/ flex relay output        didn't use don't know Pink/Black + flex relay input 87a key side        didn't use don't know RED / Black + fused 30A accessory/starter input constant NC      no connection I also notice when i do my remote start once you take out the key off the ignition my battery icon from the dash board comes on. if you started the car remotely the battery icon from the dash board also comes on and after you turn the ignition with the key in it the battery icon comes off. i don't have this problem when i did my 1998 rav 4 with viper 5701 with a remote start as well. Main Harness, 6-pin connector Red + 12vDC constant input        yes Black  - chassis groundyes Brown  + siren output yes WHITE/ Brown    parking light isolation wire     didn't use don't know Whiteparking light output yes Orange - ground when armed output       no Door Lock, 3-pin connector Blue- unlock output yes Green  - lock output   yes Auxiliary/Shutdown/Trigger Harness Pink/White     - ignition 2/flex output no Blue/White    - 2nd status/rear defogger output didn't use don't know RED / White        trunk release      no BLACK / YELLOW     dome light output yes Dark Blue        status output       i used this to by pass my clutch WHITE/ Black        don't know WHITE/ Violet        don't know ORANGE / Black        don't know Gray hood pin input     yes Blue trunk pin/instant trigger input      no WHITE/ Blue activation input don't know Violet/White      tachometer input   tied in from black wire igniter BLACK/ White    - parking brake inputyes GREEN/ Black - factory alarm disarm output didn't use don't know Green door input     yes BROWN / Black    - horn honk output i would like to use this don't know Pink  - ignition 1 output no Violet + door input        no Violet/Black    - aux 2 output      no Brown  + brake shutdown input yes Violet / YELLOW     - starter output      didn't use   don't know Gray/Black        - diesel wait to start input didn't use don't know Orange  - accessory output     didn't use don't know GREEN / WHITE   - factory alarm arm output didn't use don't know please i need your help

Alarm Harness        Description Car Harness Pink + ignition 1 input/output        BLACK/ Orange RED / White + fused (30A) ignition 2/flex relay input 87        constant Orange +   accessory output      grey Violet     + starter output car side of the starter kill blk/wht Green      + starter input key side of the starter kill blk/wht Red        + fused 30A ignition 1 input        constant Pink/White + ignition 2/ flex relay output Blue/Red   ***Set to IGN2   -   default Pink/Black + flex relay input 87a key side not used RED / Black + fused 30A accessory/starter input   constant NC      no connectionSoldering is fun!

kreg when you say set to ignition 2. where is ignition 2 (blue/red)actually is. is this why my dash board light does not come on? is this also the reason why my dome light does not come on when you arm/disarm, remote starts? i will try this out and i will let you know. thanks for the help

The Blue/Red wire should be another wire in the main ignition switch harness, where you found the other ignition wires. As always, test for it with your DMM and make quality solder connections. Soldering is fun!

thanks Kreg i got it. i still want to make my dome light to come on when dis arming the system. it says in the manula to use the BLACK / YELLOW from the 24-pin but when i connected this to my RED / White car harness for my dome light it does not work properly my dome light is dim. when i meter the wire -12volts constant. don't understand why? i also want to make my defroster to work if it's possible

still confuse. still can not make my dome light to work for my 1991 celica with viper 5904v. i need help please my transponder led does not blink as well but a have a dim constant blue light on my tranponder antenna. everything works i wonder why?

You might have a bad ground. Check the voltage between your ground point and any of the fuses. Or, you're in valet mode.