the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

code alarm ca6553


Post ReplyPost New Topic
< Prev Topic Next Topic >
josephjonesjr 
Member - Posts: 7
Member spacespace
Joined: November 14, 2013
Location: Massachusetts, United States
Posted: November 15, 2013 at 7:46 AM / IP Logged  
I have the code alarm ca6553. I am unsure how the starter kill relay is wired? The remote start does not activate, the lights flash great! The "starter input key side" and the "ignition +" is my issue. The doors locks do not respond with the remote. I did review the many diagrams on line, just does not"click".
auto enhancers 
Copper - Posts: 203
Copper spacespace
Joined: April 09, 2012
Location: Indiana, United States
Posted: November 16, 2013 at 9:13 AM / IP Logged  
we need more info, what kind of vehicle, I think you may have more issues if the locks are not working.
josephjonesjr 
Member - Posts: 7
Member spacespace
Joined: November 14, 2013
Location: Massachusetts, United States
Posted: November 17, 2013 at 6:52 PM / IP Logged  
The vehicle is the 2002 Chevy Tahoe. The current issue is with the FlashLogic(Flcan)interface module that does not program according to the instructions. I am not seeing how the ca6553 controls the vehicle locks. The vehicle has factory auto locks. I am trying to avoid the 3 pin output door lock harness. It is a part of the ca6553.
auto enhancers 
Copper - Posts: 203
Copper spacespace
Joined: April 09, 2012
Location: Indiana, United States
Posted: November 17, 2013 at 7:57 PM / IP Logged  
The fl can is a bit of an over kill on the vehicle as it only does transponder. Locks will have to be wired from the rs unit and they are pos not neg.
ign+ goes to pos ign and starter input key side goes to the switch side of the starter wire.
josephjonesjr 
Member - Posts: 7
Member spacespace
Joined: November 14, 2013
Location: Massachusetts, United States
Posted: November 19, 2013 at 8:28 AM / IP Logged  
I appreciate the information. I used the Directed Gm door lock interface 555l. It appears to function accordingly. However, the door lock function does not activate with the ca6553. I have not connected the door lock connector. I would like to program the remote of the ca6553 with the keyless entry of my vehicle. The documentation claims the ability to learn other transmitters.
josephjonesjr 
Member - Posts: 7
Member spacespace
Joined: November 14, 2013
Location: Massachusetts, United States
Posted: November 19, 2013 at 8:32 AM / IP Logged  
I have a 2002 Chevy Tahoe, with the passlock 2. I am using the code alarm ca6553 alarm\remote start. I would like to have the dome light flash with the alarm. What is the proper wiring tech?
sparkyssb 
Copper - Posts: 205
Copper spacespace
Joined: March 09, 2002
Location: United States
Posted: November 19, 2013 at 10:37 AM / IP Logged  
There are a couple of different ways you can tackle this.
1.) You could cut the parking light output wire from the CA6553 (white wire - 4pin harness) and put in a diode [to prevent backfeed] and use that wire to power the domelight.
2.) You could tap off the siren output wire from the CA6553 (brown wire - 4pin harness) to drive a simple turn signal flasher relay to power the domelight.
I'm not sure if your dome light is - or + switched so you may need to use a relay if it is - switched.
josephjonesjr 
Member - Posts: 7
Member spacespace
Joined: November 14, 2013
Location: Massachusetts, United States
Posted: November 19, 2013 at 3:56 PM / IP Logged  
I would like to use the remote for my code alarm ca6553, with the existing chevy Tahoe keyless entry. I did try programming the remote.
sparkyssb 
Copper - Posts: 205
Copper spacespace
Joined: March 09, 2002
Location: United States
Posted: November 20, 2013 at 7:25 AM / IP Logged  
I'm slightly confused. Your previous post state you are using a Directed 555L unit. That unit is simply a GM Passlock bypass kit. It has nothing to do with lock integration.
I think you'll just have to tap the door lock/unlock wires using the 3 pin harness and then you can soley use the ca6553 remote. You will need to use a relay for both of those triggers as the remote start outputs a - pulse but your truck needs a + pulse for its door locks.
josephjonesjr 
Member - Posts: 7
Member spacespace
Joined: November 14, 2013
Location: Massachusetts, United States
Posted: November 20, 2013 at 2:18 PM / IP Logged  
Thanks for the info! Now I have a different issue. The door locks work. The remote start works. In the armed mode, when the remote start is activated, the alarm sounds. The LED flashes twice, for hood/trunk. I didn't use the trunk wire. The hood pin was not used the wire is grounded. The "purple" wire the door trigger + output,for the code alarm ca6553, is not connected. The vehicle "dome light" wire gray/black at the BCM, is negative with the open. It shows positive when the door is closed and the dome light off.
I require a solution to my wiring issue!
Page of 2

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Monday, October 25, 2021 • Copyright © 1999-2021 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer