viper 4105v no start

Home / the12volt's Install Bay / Car Security and Convenience / viper 4105v no start (

Topic Closed)

Welcome Guest :)

Members

Search

Register

Login

< Prev Topic Next Topic >

corvette81

Member - Posts: 3

Joined: January 15, 2015

Location: Alberta, Canada

Posted: January 15, 2015 at 10:54 AM / IP Logged

I have installed a Viper 4105v remote start in '03 Chev Tracker, auto trans, no PDL, no theft deterrent. Park lights flash with lock/unlock buttons, horn chirps. Remote start does not attempt to start vehicle. No clicks, no LED flash, nothing.

Any ideas? What can I test?

Thanks

Back to Top

auto enhancers

Copper - Posts: 203

Joined: April 09, 2012

Location: Indiana, United States

Posted: January 15, 2015 at 12:43 PM / IP Logged

how do you have the parking brake wire connected? do you have a hood pin installed?

Back to Top

Search for other posts by auto enhancers

corvette81

Member - Posts: 3

Joined: January 15, 2015

Location: Alberta, Canada

Posted: January 15, 2015 at 12:46 PM / IP Logged

Hood pin is installed and confirmed not grounded

Brake switch input connected to foot brake. Do not have a park brake connection, it is an auto transmission

Back to Top

ziggyb222

Silver - Posts: 593

This member has made a donation to the12volt.com. Click here for more info.

Joined: January 04, 2004

Location: Maine, United States

Posted: January 16, 2015 at 6:08 PM / IP Logged

Where do you have the BLACK/ wht wire from the viper hooked up?

Back to Top

davep.

Gold - Posts: 641

Joined: May 27, 2011

Location: California, United States

Posted: January 16, 2015 at 10:26 PM / IP Logged

DEI Remote Starters have a shutdown diagnostic. It will tell you what caused the failure to start. Ie, where to look for the problem. "Shutdown" includes failure to start.

To enter shutdown diagnostic mode:

1. Turn the ignition off.

2. Press and hold the Program switch.

3. Turn the ignition on and then off.

4. Release the Program switch.

5. Press and release the Program switch.

The LED reports the last system shutdown by flashing for one minute in

the following grouped patterns and stops flashing when the ignition is

turned on.

Shutdown Flash Patterns:

1 System timed out

2 Over-rev shutdown

3 Low or no RPM, Low battery (for voltage & Virtual tach modes)

4 Remote control shutdown (or wht/blu wire)

5 (-) Hood shutdown [gry wire grounded]

6 (+) Brake shutdown [brown wire has 12V present]

7 Neutral safety [blk/wht wire NOT grounded]

Back to Top

corvette81

Member - Posts: 3

Joined: January 15, 2015

Location: Alberta, Canada

Posted: February 04, 2015 at 4:31 PM / IP Logged

Connecting this wire to ground corrected the problem. Thanks for the feedback!

Back to Top

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

viper 4105v no start

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.