the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

Remote start install now have vdc / slip errors


Post ReplyPost New Topic
< Prev Topic Next Topic >
mattgintx 
Member - Posts: 10
Member spacespace
Joined: June 09, 2015
Posted: July 29, 2015 at 8:56 PM / IP Logged Link to Post Post Reply Quote mattgintx
I installed a viper 5706v along with idatalink Acla bypass in a Nissan Murano 2009.
The remote start works fine other then ever since I installed it I have a vdc and slip light lit on my dashboard. Any ideas what could be causing this with a remote start install?
I tried disconnecting the power to the alarm and I still get the lights.
We used data 2 data. I can post the connections if necessary,
Thanks for any insight/help
dasbogie 
Silver - Posts: 514
Silver spacespace
Joined: September 30, 2006
Location: Pennsylvania, United States
Posted: July 30, 2015 at 5:26 AM / IP Logged Link to Post Post Reply Quote dasbogie
did you power all ignition wires and did you program them accordingly? In other words if you have a 2nd accessory wire in the vehicle that drops during crank, is the viper doing the same thing. Sometimes warning lights arise because something either isn't getting powered when it should be or is being powered when it shouldn't be. Did you unplug any switches that may not have been plug back in or didn't click all the way?
Advanced
mpe235 
Copper - Posts: 90
Copper spacespace
Joined: December 04, 2005
Location: New York, United States
Posted: July 30, 2015 at 5:36 PM / IP Logged Link to Post Post Reply Quote mpe235
Make sure the awd switch is plugged in .
Nissan Master Tech.
george28 
Member - Posts: 18
Member spacespace
Joined: May 19, 2015
Posted: July 30, 2015 at 8:37 PM / IP Logged Link to Post Post Reply Quote george28
I'm Matt's brother and worked on the install with him. We used idatalinks instructions found here http://cdncontent2.idatalink.com/corporate/Content/Manuals/DL-NI5/ADS-AL(DL)-NI5-EN_20150212.pdf
We used type 1 as described. We connected the Ingition + output in parallel with the idatalink ignition + input (spliced them together) and soldered them to wire connected to the odbii pin 8 location. We used a 1n4001 diode with stripe side towards viper alarm on the wire that connects the ignition + output to the bypass + input splice. The install didn't call for a 2nd ignition wire connection. @dasbogie - what do you mean by programming the ignition wires accordingly? all of the 12v constants from viper were spliced together and wired to battery with inline fuse. We did not connect the connections shown in red as it was the intention to install d2d in 2 way. thanks for all of the help and if its helpful I can list all connections but it basically follows the install guide linked above down to a T.
mattgintx 
Member - Posts: 10
Member spacespace
Joined: June 09, 2015
Posted: July 30, 2015 at 9:27 PM / IP Logged Link to Post Post Reply Quote mattgintx
mpe235 wrote:
Make sure the awd switch is plugged in .
On my murano their isn't an awd switch
kreg357 
Platinum - Posts: 7,531
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: January 30, 2009
Location: New York, United States
Posted: July 31, 2015 at 4:05 AM / IP Logged Link to Post Post Reply Quote kreg357
The iDatalink install guide you listed above is for the ADS version of firmware.  Probably just a slight mix-up.  The correct install
guide is the DBI version of firmware ( #20852 ).  The wiring is the same.  The main point, though, is you want to check to see
exactly which firmware is flashed on to the ADS AL-CA module.  It must be DBI-AL(DL)-NI5.  This is the correct firmware to
support the Vipers DBI D2D communication protocol.
Soldering is fun!
mattgintx 
Member - Posts: 10
Member spacespace
Joined: June 09, 2015
Posted: August 16, 2015 at 11:23 AM / IP Logged Link to Post Post Reply Quote mattgintx
Finally got some time. I checked the module and its indeed flashed with Dbi-al(Dl)-ni5(v1.6)
After using the remote start for a while now I've noticed about 20% of the time the car auto shuts off as soon as I open the door even if the timer hasn't gone down. I can't seem to find anything that triggers when it shuts off and when it stays running
mattgintx 
Member - Posts: 10
Member spacespace
Joined: June 09, 2015
Posted: August 16, 2015 at 1:25 PM / IP Logged Link to Post Post Reply Quote mattgintx
To add a little more I've checked all harnesses and they are fully connected.
Also had autozone connect to the obd port and its throwing p0603 if that helps

If you wish to post a reply to this topic, you must first login.
If you are not already registered, you must first register.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Monday, December 6, 2021 • Copyright © 1999-2021 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer