the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

ICBM-7071 Alarm install in 99 Ford Escort ZX2


Post ReplyPost New Topic
< Prev Topic Next Topic >
antman1 
Copper - Posts: 121
Copper spacespace
Joined: February 13, 2012
Location: Tennessee, United States
Posted: June 16, 2016 at 2:07 PM / IP Logged Link to Post Post Reply Quote antman1
Well I must say I didnt think I was gonna get another one of these alarms but they tend to be working out over all and now my daughter bought a car and wants the same one I have like in the past so I got her one. This one will be a little different because it is going in her 99 Ford Escort ZX2 with Automatic transmission. It doesnt have power locks so I will be adding 2 door lock motors (Aftermarket) when I do the install.
The user manual for the Alarm is found here: ICBM 7101
and I am going to include a rough draft of my wiring I have figured out so far and was wondering if anyone might be able to look over it and tell me if it looks good or if I missed anything. Also I am not sure on the wires to do for the door triggers when the door is opened to set the alarm off. Thank you all in advance.
ICMB-7071 Wiring DRAFT for 99 Ford Escort ZX2
5 Pin Heavy Gauge Harness:
Red - Battery Constant 12v+ Positive Wire (+): Battery Constant 12v+ Positive Wire (+): Black
Battery Constant 12v+ Positive Wire Location: Ignition Switch Harness
Purple - Starter Positive Wire (+): Starter Positive Wire (+): RED / White
Starter Positive Wire Location: Ignition Switch Harness
Orange - Accessory Positive Wire (+): Accessory Positive Wire (+): BLACK/ Red
Accessory Positive Wire Location: Ignition Switch Harness
   
Pink A - Ignition Positive Wire (+): Ignition Positive Wire (+): Blue
Ignition Positive Wire Location: Ignition Switch Harness
Pink B - Second Ignition Positive Wire (+): Second Ignition Positive Wire (+): BLACK/ White
Second Ignition Positive Wire Location: Ignition Switch Harness
    
7 Pin Secondary (H4) Harness:
1-3 - Factory wiring to R/S module
4 - Blue/White - N/C
5 - Gray/Black - N/C
6 - BLACK/ White - Chassis Ground
7 - Violet/White - Tachometer Wire Negative Wire (-): Tachometer Wire Negative Wire (-): Yellow/Blue
Tachometer Wire Negative Wire Location: Or RED / Light Blue or Blue/Light Green (Coil 2 Cylinder)
10 Pin Primary (H1) Harness
1 - Brown - To Siren (+) input
2 - White - Parking Light Positive Wire (+): Pin 30 of Relay as seen below.
*Will need to use a relay to convert the (+) to (-). Just a standard 30a/40a automotive relay connected as follows:
Pin 85 - GROUND
Pin 86 - GROUND
Pin 87 - Parking Light Negative Wire (-): RED / Black
Parking Light Negative Wire Location: 15 Pin Green Connector below Fuse Panel
Pin 30 - pin 2 of (H1) Harness on Alarm - White - Parking Light Positive Wire (+): Brown
3 - Violet - N/C
4 - Blue/Black - Power Door Unlock Negative Wire (-):(Adding Aftermarket Universal actuators for door lock, will require relays)
Relay 1
Pin 85 - 12v constant
Pin 86 - 4 - Blue/Black - Power Door Unlock Negative Wire (-) on Alarm
Pin 87 - 12v constant
Pin 87a- Ground
Pin 30 - Door Motor on right and left
5 - BROWN / Black - Chassis Ground
6 - Violet/Black - N/C
7 - GREEN/ Black - Power Door Lock Negative Wire (-):(Adding Aftermarket Universal actuators for door lock, will require relays)
Relay 2
Pin 85 - 12v constant
Pin 86 - 7 - GREEN/ Black - Power Door Lock Negative Wire (-)
Pin 87 - 12v constant
Pin 87a- Ground
Pin 30 - Door Motor on right and left
8 - WHITE/ Black - Chassis Ground
9 - Red - 12v Constant fused (can tie into heavy gauge red wire from main harness)
10 - Black - Chassis Ground
6 Pin Secondary (H2) Harness:
1 - Orange - Starter kill relay input: Goes to (-) on LED/Scanner bar to enable when alarm is armed
2 - Blue - N/C
3 - WHITE/ Black - N/C
4 - PURPLE / Black - N/C
5 - BLACK/ White - N/C
6 - RED / White - N/C
8 Pin (H3) Harness:
1 - GREEN/ Black - N/C
2 - GREEN / WHITE - N/C
3 - Black - Trunk Pin Switch Negative Wire (-): RED / Yellow
Trunk Pin Switch Negative Wire Location: Driver’s Kick Large Harness
4 - Gray - Must add aftermarket hood pin.
5 - Brown - Brake Light Positive Wire (+): Brake Light Positive Wire (+): Green
Brake Light Positive Wire Location: Brake Switch
6 - Yellow - Pink wire from main harness
7 - Green - Negative Door Input (-): **Not Sure on this one yet**
8 - Purple - N/C
**EDIT - ADDED RELAY WIRING FOR DOOR LOCKS**
antman1 
Copper - Posts: 121
Copper spacespace
Joined: February 13, 2012
Location: Tennessee, United States
Posted: June 18, 2016 at 4:48 PM / IP Logged Link to Post Post Reply Quote antman1
for the 8 Pin (H3) Harness does this look right as well as the rest of the connections in my draft??
8 Pin (H3) Harness
7 - Green - Negative Door Input (-): Power Door Trigger Negative Wire (-): RED / White
Power Door Trigger Negative Wire Location: Under Fuse Panel
ICMB-7071 Wiring DRAFT for 99 Ford Escort ZX2
5 Pin Heavy Gauge Harness:
Red - Battery Constant 12v+ Positive Wire (+): Battery Constant 12v+ Positive Wire (+): Black
Battery Constant 12v+ Positive Wire Location: Ignition Switch Harness
Purple - Starter Positive Wire (+): Starter Positive Wire (+): RED / White
Starter Positive Wire Location: Ignition Switch Harness
Orange - Accessory Positive Wire (+): Accessory Positive Wire (+): BLACK/ Red
Accessory Positive Wire Location: Ignition Switch Harness
    
Pink A - Ignition Positive Wire (+): Ignition Positive Wire (+): Blue
Ignition Positive Wire Location: Ignition Switch Harness
Pink B - Second Ignition Positive Wire (+): Second Ignition Positive Wire (+): BLACK/ White
Second Ignition Positive Wire Location: Ignition Switch Harness
     
7 Pin Secondary (H4) Harness:
1-3 - Factory wiring to R/S module
4 - Blue/White - N/C
5 - Gray/Black - N/C
6 - BLACK/ White - Chassis Ground
7 - Violet/White - Tachometer Wire Negative Wire (-): Tachometer Wire Negative Wire (-): Yellow/Blue
Tachometer Wire Negative Wire Location: Or RED / Light Blue or Blue/Light Green (Coil 2 Cylinder)
10 Pin Primary (H1) Harness
1 - Brown - To Siren (+) input
2 - White - Parking Light Positive Wire (+): Pin 30 of Relay as seen below.
*Will need to use a relay to convert the (+) to (-). Just a standard 30a/40a automotive relay connected as follows:
Pin 85 - GROUND
Pin 86 - GROUND
Pin 87 - Parking Light Negative Wire (-): RED / Black
Parking Light Negative Wire Location: 15 Pin Green Connector below Fuse Panel
Pin 30 - pin 2 of (H1) Harness on Alarm - White - Parking Light Positive Wire (+): Brown
3 - Violet - N/C
4 - Blue/Black - Power Door Unlock Negative Wire (-):(Adding Aftermarket Universal actuators for door lock, will require relays)
Relay 1
Pin 85 - 12v constant
Pin 86 - 4 - Blue/Black - Power Door Unlock Negative Wire (-) on Alarm
Pin 87 - 12v constant
Pin 87a- Ground
Pin 30 - Door Motor on right and left
5 - BROWN / Black - Chassis Ground
6 - Violet/Black - N/C
7 - GREEN/ Black - Power Door Lock Negative Wire (-):(Adding Aftermarket Universal actuators for door lock, will require relays)
Relay 2
Pin 85 - 12v constant
Pin 86 - 7 - GREEN/ Black - Power Door Lock Negative Wire (-)
Pin 87 - 12v constant
Pin 87a- Ground
Pin 30 - Door Motor on right and left
8 - WHITE/ Black - Chassis Ground
9 - Red - 12v Constant fused (can tie into heavy gauge red wire from main harness)
10 - Black - Chassis Ground
6 Pin Secondary (H2) Harness:
1 - Orange - Starter kill relay input: Goes to (-) on LED/Scanner bar to enable when alarm is armed
2 - Blue - N/C
3 - WHITE/ Black - N/C
4 - PURPLE / Black - N/C
5 - BLACK/ White - N/C
6 - RED / White - N/C
8 Pin (H3) Harness:
1 - GREEN/ Black - N/C
2 - GREEN / WHITE - N/C
3 - Black - Trunk Pin Switch Negative Wire (-): RED / Yellow
Trunk Pin Switch Negative Wire Location: Driver’s Kick Large Harness
4 - Gray - Must add aftermarket hood pin.
5 - Brown - Brake Light Positive Wire (+): Brake Light Positive Wire (+): Green
Brake Light Positive Wire Location: Brake Switch
6 - Yellow - Pink wire from main harness
7 - Green - Negative Door Input (-): Power Door Trigger Negative Wire (-): RED / White
Power Door Trigger Negative Wire Location: Under Fuse Panel
8 - Purple - N/C
antman1 
Copper - Posts: 121
Copper spacespace
Joined: February 13, 2012
Location: Tennessee, United States
Posted: June 23, 2016 at 9:43 PM / IP Logged Link to Post Post Reply Quote antman1
I think I have all the wires figured out except I am curious if I got the "7 - Green - Negative Door Input (-)" right or not? also curious if it needs a diode
antman1 
Copper - Posts: 121
Copper spacespace
Joined: February 13, 2012
Location: Tennessee, United States
Posted: July 05, 2016 at 1:12 PM / IP Logged Link to Post Post Reply Quote antman1
I just wanted to let everyone know that everything worked fine with my install. I had to install a relay for the trunk release and for the door output I installed a Diode just to be sure. works great.
Getting wire through the firewall was tricky but I drilled a hole in the plate covering the spot a Clutch pedal would have been at and ran it through there and put Gorilla Glue on it to keep it insulated from rubbing on the hole I cut.
Only issue I ran into was the starter kill wire that I would use to activate the LED/Scanner bar would not work. o'well, I just wired it to come on when the car is off and go off when the car is cranked.

If you wish to post a reply to this topic, you must first login.
If you are not already registered, you must first register.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Wednesday, January 19, 2022 • Copyright © 1999-2022 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer