the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2006 Mazda Tribute cruise control wiring diagram


Post ReplyPost New Topic
< Prev Topic Next Topic >
sillywilly 
Member - Posts: 17
Member spacespace
Joined: August 18, 2017
Location: Arizona, United States
Posted: October 24, 2017 at 9:06 PM / IP Logged Link to Post Post Reply Quote sillywilly
Does anyone have a cruise control wiring diagram for a 2006 Mazda Tribute?
Ween 
Platinum - Posts: 1,334
Platinum spacespace
Joined: August 01, 2004
Location: Illinois, United States
Posted: October 24, 2017 at 9:28 PM / IP Logged Link to Post Post Reply Quote Ween
http://www.revbase.com/BBBMotor/Wd/DownloadPdf?id=129476
sillywilly 
Member - Posts: 17
Member spacespace
Joined: August 18, 2017
Location: Arizona, United States
Posted: November 13, 2017 at 3:21 PM / IP Logged Link to Post Post Reply Quote sillywilly
I used the link and printed out the wiring diagram. Thank you!
I need someone's input on the troubleshooting I've done so far.
2006 Mazda Tribute: Cruise control does not engage; light on instrument panel does not illuminate
I checked the following input and output pins on the Speed Control Servo
- pin 7 has 12v with ignition switch on
- verified ground on pin 10
- pin 9 goes from 12v to 0v when the brake pedal is pushed
- pin 4 goes from 0v to 12v when the brake pedal is puched
- pin 6 (which appears to supply voltage to ON/OFF, RESUME, COAST, and SET resistor/switches) has zero volts
Are there any other t/s steps I should take before assuming the Speed Control Servo is bad?
Thanks
Ween 
Platinum - Posts: 1,334
Platinum spacespace
Joined: August 01, 2004
Location: Illinois, United States
Posted: November 13, 2017 at 6:23 PM / IP Logged Link to Post Post Reply Quote Ween
Pin 1 @ Air Bag connector should have +12V with ignition on.
Pin 3 @ Air Bag connector should have voltage (unknown value, should be less than ignition voltage) when cruise is switched on at steering wheel.
Pin 2 as Pin 3 above i.e. continuity between 2 & 3 as long as other cruise control buttons aren't pressed. When buttons are pressed voltage (unknown again) will be present.
sillywilly 
Member - Posts: 17
Member spacespace
Joined: August 18, 2017
Location: Arizona, United States
Posted: November 13, 2017 at 10:06 PM / IP Logged Link to Post Post Reply Quote sillywilly
Thanks Ween! Your suggestions make sense.
I have to to to Texas to do some hurricane relief work for a week, so I won't get those measurements until I get back. I'll let you know what I get when I'm back.
Thanks again!

If you wish to post a reply to this topic, you must first login.
If you are not already registered, you must first register.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Saturday, January 22, 2022 • Copyright © 1999-2022 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer