the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

Viper 350 Plus 3105V, Door Lock Actuators


Post ReplyPost New Topic
< Prev Topic Next Topic >
chev104275 
Gold - Posts: 1,424
Gold spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: November 26, 2007
Location: Massachusetts, United States
Posted: April 16, 2024 at 8:11 AM / IP Logged Link to Post Post Reply Quote chev104275
So, did grounding the trigger wires for the relay operate the locks as they should? How are you testing the Lock wiring from the module? Red on 12v black on either blue or green and active the locks during the lock command the meter should read 12v? You may need to diode isolate the lock wires from the relay pin Band would go towards the module.
If i Can't Install it    I Don't need it   Joe
chiel 
Member - Posts: 8
Member spacespace
Joined: April 03, 2024
Location: Netherlands
Posted: April 16, 2024 at 8:41 AM / IP Logged Link to Post Post Reply Quote chiel
Unfortunately, grounding made no difference.
If I insert the connector with green and blue wires diagonally into the computer (so then it makes contact on 1 pin) then the actuators work fine. As soon as I put it in properly, it stops working. And, the relays remain energized and get hot.
But is it normal for the trigger wires to be close to 12V?? As you can read, its my first time.
Thanks.
chev104275 
Gold - Posts: 1,424
Gold spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: November 26, 2007
Location: Massachusetts, United States
Posted: April 16, 2024 at 9:15 AM / IP Logged Link to Post Post Reply Quote chev104275
So, I think were missing something. if you look at the diagram you used and you remove the green on 86 and the blue from 85. Then use a jumper wire to ground on the pins of the relays the actuators should work if everything is wired correctly. If they don't work, then I would look at the wiring of the relays again. If they do work, then recheck the output of the module and make sure it is outputting a ground signal.
If i Can't Install it    I Don't need it   Joe
amcclay 
Member - Posts: 4
Member spacespace
Joined: March 12, 2024
Location: California, United States
Posted: April 18, 2024 at 12:20 PM / IP Logged Link to Post Post Reply Quote amcclay
Do you have one of these hooked up?
https://a.co/d/0ci4IYZ
I used the same actuator system and this was required to make them work.
Miata
t&t tech 
Platinum - Posts: 2,608
Platinum spacespace
Joined: October 05, 2008
Location: Trinidad and Tobago
Posted: April 18, 2024 at 6:10 PM / IP Logged Link to Post Post Reply Quote t&t tech
amcclay wrote:
Do you have one of these hooked up?
https://a.co/d/0ci4IYZ
I used the same actuator system and this was required to make them work.
The equivalent of two five pin SPDT Relays.
commit your way to jehovah and he will act in your behalf. psalms 37:5
chiel 
Member - Posts: 8
Member spacespace
Joined: April 03, 2024
Location: Netherlands
Posted: April 19, 2024 at 10:06 AM / IP Logged Link to Post Post Reply Quote chiel
I use de 5p relais.
Everything works when I put 12V on one pin. The actuator opens and closes.
It doesn't work when I plug it into the controlbox. Both open and close pins in the controlbox are 12V at the same time and don't give a pulsesignal when i use de remote.
Grtz.
Page of 2

If you wish to post a reply to this topic, you must first login.
If you are not already registered, you must first register.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Sunday, April 21, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer