Please I need help (alarm)

Home / the12volt's Install Bay / Car Security and Convenience / Please I need help (alarm) (

Topic Closed)

Welcome Guest :)

Members

Search

Register

Login

< Prev Topic Next Topic >

michaeltam2k

Member - Posts: 30

Joined: September 02, 2003

Location: United States

Posted: September 22, 2003 at 10:42 PM / IP Logged

I need help on my alarm installation . I did everything except when I remote start my car when it arm my factory alarm when off . Please help me on this thank you so much . My car is toyota sequoia 2003 and again thank you .

Back to Top

c2deez

Copper - Posts: 71

Joined: June 17, 2002

Location: United States

Posted: September 23, 2003 at 6:46 PM / IP Logged

The wire for OEM disarm should be red\yellow(-) INSIDE the driver door.

Back to Top

michaeltam2k

Member - Posts: 30

Joined: September 02, 2003

Location: United States

Posted: September 24, 2003 at 8:39 PM / IP Logged

dear c2deez , i did as you told but it doesn't work can you do so research and let me know please thank you so much ...

Back to Top

securinu

Silver - Posts: 772

This member has made a donation to the12volt.com. Click here for more info.

Joined: September 15, 2002

Location: United States

Posted: September 24, 2003 at 9:36 PM / IP Logged

you need to split the lock sense wire with lock unlock wires i did one 3 days ago you need to unlock first then start then relock.

Joe O'Byrne

Owner / Installer

Back to Top

JWorm

Platinum - Posts: 2,208

Joined: December 11, 2002

Location: New Hampshire, United States

Posted: September 24, 2003 at 10:56 PM / IP Logged

Did you get the locks working on the aftermarket alarm? Those locks aren't too easy for a rookie.

To disarm the factory alarm when you remote start, you must ground the trucks keysense wire during remote start. Connect the ground when running wire from the remote start to the keysense wire. I haven't done one since last winter, but I think its either BLACK/ blue or blue/black in a 2-pin plug going to the key cylinder.

What alarm/remote start are you using?

Back to Top

youngblood

Copper - Posts: 77

Joined: September 22, 2003

Location: United States

Posted: September 26, 2003 at 5:02 PM / IP Logged

three wires inside the door and coming from the lock/unlock switches/power window switches......

RED / Yellow... split this wire using a standard starter kill relay.... power up the relay using the Blue/White wire fusing it accordingly.... use the remaining contact 85 or 86 depending on how you wired it. and have your lock wire go into this contact point and loop it back out and tap and terminate it to the GREEN/ black wire. The unlock wire coming from your alarm should be diode isolated, and possibly boosted depending on your alarm output, and go to both the red yellow wire(yes the same one you split with a relay) and the GREEN/ red wire

Back to Top

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Please I need help (alarm)

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.