the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2002 ford focus door locks


Post ReplyPost New Topic
< Prev Topic Next Topic >
plywood 
Member - Posts: 34
Member spacespace
Joined: July 31, 2003
Location: United States
Posted: November 26, 2003 at 1:11 PM / IP Logged  

I have installed a remote start in a 2002 ford focus. After finding the wires for the door locks and testing them, I hooked them up. However, once the car is started the factory keyless entry and the aftermarket do not work. I'm thinking that I'm going to have to go directly to the lock and unlock motors to overcome this problem. Here is a copy of the wire code I used.

Ford

Focus

2000-2002

Remote Starter Wiring Colors and Notes

Function

Vehicle Color

Location

Start:

GRAY/BLACK

IGNITION SWITCH HARNESS

Ignition #1:

GREEN/ YELLOW

IGNITION SWTICH HARNESS*

Ignition #2:

N/A

Ignition #3:

N/A

Accessory:

YELLOW

IGNITION SWITCH HARNESS

Brake Light:

GREEN/ RED (+)

AT SWITCH ABOVE PEDAL **

Tach Signal:

BLACK/ LT. GREEN

AT COIL MODULE

Parking Lights:

ORANGE / YELLOW (+)

AT LIGHT SWITCH

Headlights:

OEM Alarm Disarm:

BLUE/LIGHT GREEN

IN DRIVERS KICK PANEL

OEM Alarm Arm:

Diesel Glow Plug:

Clutch Bypass Wire:

Notes:

* This Vehicle Is Equipped With Ford's Passive Anti-Theft System. Use Universal Alarm Bypass Module part # 2x402 where X can be any number. ** This Wire Is Only Active When The Ignition Is On.


Ford

Focus

2000-2002

Alarm and Keyless Entry Wiring Colors and Notes

Function

Vehicle Color

Location

Constant +12 Volts:

RED

IGNITION SWITCH HARNESS

Starter Kill:

GRAY/BLACK

IGNITION SWITCH HARNESS

Ignition +12 Volts:

GREEN/ YELLOW

IGNITION SWTICH HARNESS*

Dome Lights/Superv:

OEM Horn:

Power Lock:

BLACK/ RED (-)

DRIVER'S KICK IN DOOR BOOT ***

Power Unlock:

BLACK / YELLOW (-)

DRIVER'S KICK IN DOOR BOOT ***

Trunk Release:

BLACK / YELLOW (-)

AT TRUNK RELEASE SWITCH

Alarm Input Wire:

Any help would be greatly appericatied. Thank You

Matt

Chapioshzx3 
Member - Posts: 3
Member spacespace
Joined: January 25, 2004
Location: Mexico
Posted: January 27, 2004 at 12:37 PM / IP Logged  

Hi do you know the color of the cable, of The OEM Alarm arm?

Thanks

Chapiosh
rODRIGUE 
Member - Posts: 7
Member spacespace
Joined: December 30, 2003
Location: Canada
Posted: January 28, 2004 at 9:56 PM / IP Logged  
plug BLACK/ green and BLACK / YELLOW at the unlock off your kit, with two diode....
plywood 
Member - Posts: 34
Member spacespace
Joined: July 31, 2003
Location: United States
Posted: February 03, 2004 at 9:25 AM / IP Logged  
I've got the problem fixed. Thanks for the input.  I got the wire were they go into the bcm dehind the glove box.
Matt
Always remember to test wires with a Digital Multimeter!

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Tuesday, June 18, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer