Amps Going into protection Mode

Home / the12volt's Install Bay / Car Audio / Amps Going into protection Mode (

Topic Closed)

Welcome Guest :)

Members

< Prev Page Next Page > < Prev Topic Next Topic >

Sebastian018

Silver - Posts: 364

This member has made a donation to the12volt.com. Click here for more info.

Joined: November 01, 2002

Location: United States

Posted: January 25, 2004 at 12:20 AM / IP Logged

OK, I will do that tomorrow.........

the subs are new!!! Brand new package sealed....

mobiletoys2002

Gold - Posts: 1,050

Joined: April 12, 2002

Location: United States

Posted: January 25, 2004 at 12:23 AM / IP Logged

my bad you are running one sub to each amp right? If so that is fine leave it like that>I was thinking something else

mobiletoys2002

Gold - Posts: 1,050

Joined: April 12, 2002

Location: United States

Posted: January 25, 2004 at 12:24 AM / IP Logged

Does this only happen at high volume levels?

Sebastian018

Silver - Posts: 364

Joined: November 01, 2002

Location: United States

Posted: January 25, 2004 at 12:37 AM / IP Logged

No, I was listening at low volumen, then i turn it a little bit higher and it went into protection mode....

customsuburb

Gold - Posts: 1,813

Joined: January 17, 2004

Location: United States

Posted: January 25, 2004 at 10:20 AM / IP Logged

So your subs are 2 ohm dvc? If they are then you cant get a 2 ohm impedance from each one if you wire them to their own amp. You can only get either a 4 ohm load or a 1 ohm load like this: Amps Going into protection Mode - Page 3 -- posted image. Tell me if this is what you are doing.

Sebastian018

Silver - Posts: 364

Joined: November 01, 2002

Location: United States

Posted: January 25, 2004 at 10:58 AM / IP Logged

NO My subs are dual 4ohms DVC< It can only be wire into 2ohms or 4 ohms..

Sebastian018

Silver - Posts: 364

Joined: November 01, 2002

Location: United States

Posted: January 25, 2004 at 11:01 AM / IP Logged

and They way i have is like this

Amps Going into protection Mode - Page 3 -- posted image.

Sebastian018

Silver - Posts: 364

Joined: November 01, 2002

Location: United States

Posted: January 25, 2004 at 11:02 AM / IP Logged

Sebastian018

Silver - Posts: 364

Joined: November 01, 2002

Location: United States

Posted: January 25, 2004 at 11:13 AM / IP Logged

well they way i did it was positive of one coil to positive of the other coild and to the amp same with the negative..(2 ohms)

Sebastian018

Silver - Posts: 364

Joined: November 01, 2002

Location: United States

Posted: January 25, 2004 at 2:50 PM / IP Logged

OK, GUYS< I took everything out ( i have a custom instalation( so it took me like 3 hours to take it out so i can change the grounds... I did changed BUT STILL THE SAME PROBLEM< I WAS LIKE HOW COME< 4 HOURS FOR Nothing.. Them I star thinking what else could it be, and I just got last week the AUdio Processor pioneer DEQ-9200 and it was in PRO Mode, so i star reading the mannual and i change two seetings , one intead of the bass to be stereo i select mono, and The setting of the bass was really high like at 6, so i put in at 4 and i did some other changes i tested, and It seems to work, because before like after 5 minutes it went to protection, now i did it for 10 minutes nothing happens, so i think that was the problem i will check out again for more than 10 minutes...

thank you for your help...

< Prev Page Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.