92 integra wont start after wires burnt

Home / the12volt's Install Bay / Vehicle Wiring Information & File Requests / 92 integra wont start after wires burnt (

Topic Closed)

Welcome Guest :)

Members

Search

Register

Login

< Prev Topic Next Topic >

jits1980

Member - Posts: 15

Joined: March 11, 2004

Location: United States

Posted: June 25, 2004 at 12:31 AM / IP Logged

i have a 92 integra. when my alarm was installed they skipped the adding a fuse part and connected the power directly to the line. well my wires burnt and now my car wont start, my ground and power wires seem to be burnt. do you think the unit is fried and that is why my car wont start? do you think i should put some new ground wires. It seems that the wires are ok, but the plastic coverering is charred. please help asap

jits

Back to Top

rudbwoy69camaro

Silver - Posts: 350

This member has made a donation to the12volt.com. Click here for more info.

Joined: June 10, 2003

Location: United States

Posted: June 29, 2004 at 7:35 PM / IP Logged

time to kick some ass if I were you...

Back to Top

Search for other posts by rudbwoy69camaro

swamprat323

Gold - Posts: 1,335

Joined: September 22, 2002

Location: Florida, United States

Posted: June 29, 2004 at 7:50 PM / IP Logged

Check all the fuses, your starter wire is BLACK/ white if you want to coneect it back togeter. I would doulbe check ALL other wires just to make sure, they are good to go.

Back to Top

Besprend

Member - Posts: 29

Joined: December 17, 2003

Location: United States

Posted: July 17, 2004 at 12:27 AM / IP Logged

That's right, time to kick someone's behind. Someone has to be liable for not properly fusing an electrical unit. Your alarm is french fried.

Back to Top

Velocity Motors

Moderator - Posts: 12,488

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Fabrication. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: July 17, 2004 at 10:19 AM / IP Logged

Make sure that all the burned wires are properly tapped up again. THis will a pain in the butt because the ignition cylinder wraps upwards and around on the right side of the steering column where's room is limited. Just make sure that none of the wires will short to ground when you get everything back together again and also go back to the place you got it done and raise some sh*t ! I would. 92 integra wont start after wires burnt - Last Post -- posted image.

92 integra wont start after wires burnt - Last Post -- posted image.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Back to Top

Search for other posts by Velocity Motors

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

92 integra wont start after wires burnt

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.