older cilfford prox sensor help

Home / the12volt's Install Bay / Car Security and Convenience / older cilfford prox sensor help (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

c7iq

Member - Posts: 15

Joined: July 26, 2004

Location: United States

Posted: September 23, 2004 at 5:16 PM / IP Logged

i got this proximity sensor for free, but i need to test it, and its not in the original casing.. can anyone tell which leads are which on this thing? it says model CSS-R1 and is a clifford if i remember right..

basicly, i dont know which knobs adjust what and which leads are what cause its not in the orig case.

[IMG]https://img.photobucket.com/albums/v95/448grams/ms1.jpg[/IMG]

[IMG]https://img.photobucket.com/albums/v95/448grams/ms2.jpg[/IMG]

c7iq

Member - Posts: 15

Joined: July 26, 2004

Location: United States

Posted: September 23, 2004 at 5:18 PM / IP Logged

older cilfford prox sensor help -- posted image.

c7iq

Member - Posts: 15

Joined: July 26, 2004

Location: United States

Posted: September 23, 2004 at 5:19 PM / IP Logged

Teken

Gold - Posts: 1,492

Joined: August 04, 2002

Location: Aruba

Posted: September 23, 2004 at 7:28 PM / IP Logged

You will not be able to use the device correctly without the remote key pad which changes the interior / exterior zones.

I am assuming you have this second part? If so, I can give you the wire output leads.

As for the actual circuit board, do not adjust anything on the unit. it is calibrated from the factory, and any adjustment without the proper testing tools will affect the field.

Regards

EVIL Teken . . .

c7iq

Member - Posts: 15

Joined: July 26, 2004

Location: United States

Posted: September 24, 2004 at 2:02 AM / IP Logged

so what are the leads?

Teken

Gold - Posts: 1,492

Joined: August 04, 2002

Location: Aruba

Posted: September 24, 2004 at 8:33 AM / IP Logged

Upon viewing the second image file the unit looks alot like the Crimestopper DFR unit.

I will varify that photo with what I have.

Regards

EVIL Teken . . .

c7iq

Member - Posts: 15

Joined: July 26, 2004

Location: United States

Posted: September 24, 2004 at 12:57 PM / IP Logged

im sure it was a cliffford, i got it out of a car at the junkyard, but i removed the casing because it had sticky crap on it .

Teken

Gold - Posts: 1,492

Joined: August 04, 2002

Location: Aruba

Posted: September 24, 2004 at 4:56 PM / IP Logged

The unit is indeed a Crimestopper unit, there are however many variations of the exact same model being sold under various brand names.

The pin out are as follows. From left to right starting at the IC chip the following pin outs are colored, and wired to the following input / outputs to your alarm system.

1. RED = +12 volt constant

2. (-) GREEN = PRE WARN Input

3. (-) BLUE = TRIGGER Input

4. (-) BLACK = ARMED OUTPUT

The green dial closest to the green LED is trigger sensitivty, the other one is the pre-warn.

You will require a molex connector, it will costs you $0.25 at any electronics store.

Regards

EVIL Teken . . .

c7iq

Member - Posts: 15

Joined: July 26, 2004

Location: United States

Posted: September 24, 2004 at 7:41 PM / IP Logged

well i was wrong, i stopped by the junkyard for another reason and happen to find the case and the harness.

its a autogage RS-32

it has a red, pink, blue, black wire in that order.

c7iq

Member - Posts: 15

Joined: July 26, 2004

Location: United States

Posted: September 24, 2004 at 7:42 PM / IP Logged

well i was wrong, i stopped by the junkyard for another reason and happen to find the case and the harness.

its a autogage RS-32

it has a red, pink, blue, black wire in that order.

how would i connect this to my compustar brain? (model cm3000 i think)

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.