here's a write up of all the connection i made from the compustar brain to the car and from the two modules. and some wiring diagram for everything.
please help me for this is the last problem i have to tackle.
this is my first installation of this kind.
thank you all
pdf manual for my compustar alarm
with wiring instruction
http://www.compustar.org/support/manuals/wiring_manuals/CM3000_wiring_manual.pdf http://www.compustar.org/support/manuals/install_manuals/CM3000_install_manual.pdfwiring diagram for my car
http://www.directechs.com/directwire/wire_body.asp?action=select&yr=5234&product=Remote%20Start http://www.directechs.com/directwire/wire_body.asp?action=select&yr=5234&product=Securitywiring diagram for HODL2 door interface
https://shop.bypasskit.com/OriginalManual/HODL2_H1S1D2_I.PDFwiring diagram for PKH3 immobilizer bypass
https://shop.bypasskit.com/OriginalManual/PKH3_H6S4D1_I.PDFconnector #1
pin1. constant power
connect to white wire at ign harness, pin 3 is wired to this also
pin2. positive parking light ouput
connect to RED / blk wire plug above fuse box
this is confirm, the parking light blink when arm/disarm alarm.
pin3. power the unit and to relay for 2nd ign/2nd acc/2nd starter. the relay is prewired. connect to white wire at ign harness, pin 1 is also wired to this.
pin4. + accessory activate blower motor for heater/AC
connect to BLACK/ red wire in ign harness
pin5. (-) when armed out pre-wired into starter-kill relay.
pin6. (+)starter output
prewired into starter-kill relay.
starter kill relay, have two lead to interrupt starter wire.
yellow/black to key side of the starter wire.
yellow connect to motor side of starter wire.
this is confirm. since the car does start with remote.
pin7. (+) ignition connect to BLACK / YELLOW in ign harness
pin8. ground
connector #2
pin1. (-) parking light output
according to diagram it's BLACK/ red or blue/red in steering column cover.
couldn't locate so didn't connect. parking light still work from (+) parking light output from connector#1 pin2
pin2. (-) status out wire
i split this wire to the two modules. Pkh3 immobilizer bypass, HODL2 doorlock interface. both from bypasskit.com
i put a diode in between the modules and the brain. to protect the brain. since it's a (-) current i place the gray dash on the diode toward the brain. is this correct?pin3,pin4 and pin5all of the above is for (-) 2nd igniton/accessory/starteri can wire the above pin to the 2nd relay to get a (+) trigger ouput.i have not yet wire any of the above to any connection.my car have a 2nd accessory. WHITE/ red in ignition harness.some one said i should wire the 2nd accessory to radio harness so the radio would come on when remote started.please advise what i should do with the above wires.Connector #3
pin1. parking brake.
did not use. i have a auto tranny. and i don't need turbo timer.
wat is turbo timer for? it suppose to keep the car running when the ebrake is engage and it shut off the car after 5 minutes? is it for car with turbo?pin2. (-) shutdown for hood trigger.
wired to HODL2 module. wire to violet/white (-)hood trigger ouput.
this is confirm. alarm won't arm when hood is open and won't remotestart car.
pin3. shutdown for foot brake.
WHITE/ blck at brake pedal switch.
confirm. car shut down when press on brake w/o key in
pin4. (-) trigger input for trunk pin.
connect to (-) trunk input orange wire in HODL2
pin5. (-) trigger input for door
connect to (-) door trigger input pink/white wire in HODL2
pin6. (+) input trigger for door
i don't have (+) trigger for door. not connected.
pin7/8 glow plug. only for diesel car. not connected.
pin9. tach wire.
connect to blue/red tach wire in ECM. confirm with compustar brain.
connector #4
pin1. no connection
pin2. (-) 200mA trunk release.
wire to a relay to convert the polarity for my (+) trunk release wire.
confirm. trunk open.
pin3. driver's door priority unlock.
not connected.
pin4. (+)/(-) lock ouput connect to lock input in HODL2
pin5. (+)/(-) lock ouput connect to unlock input in HODL2
both confirm. door unlock/lock with remote
pin6. no connection
connector #5
pin1 rearm wire
pin2 disarm wire
not connected to both. since HODL2 will disarm/arm the factory alarm.
pin3 domelight wire.
not connected. my interior light already come on when unlock.
pin4. siren output. connected and confirm
pin5. horn honk. connected and confirm.
thanks again. please provide help asap.
i'm trying to finish and clean up this whole install by this weekend.
this is the second weekend i spent on this.