Matrix 3.5 with Bitwriter

Home / the12volt's Install Bay / Car Security and Convenience / Matrix 3.5 with Bitwriter (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

joe435

Member - Posts: 7

Joined: March 15, 2004

Posted: January 15, 2005 at 5:47 PM / IP Logged

I have a 04 avalanche that I installed a matrix 3.5 on. I am attempting to use the bitwriter to have remote one tied to driver 1 and remote 2 to driver 2. How is this possible? I have called dei/clifford and they say that it is possible but that since I am not a cetified installer that I must take it to one. But they said you must have a bitwriter to do such a thing. Any ideas?

MCubed45

Copper - Posts: 65

Joined: February 27, 2003

Location: United States

Posted: January 15, 2005 at 6:15 PM / IP Logged

it's not in the install manuals an stuff on DEI's site? My viper has all the programming instructions and procedures in the install manual...

joe435

Member - Posts: 7

Joined: March 15, 2004

Posted: January 16, 2005 at 12:02 AM / IP Logged

Nothing as far as I can tell in the manual. Any other ideas?

auex

Platinum - Posts: 5,041

This member has made a donation to the12volt.com. Click here for more info.

Joined: December 23, 2002

Location: Arizona, United States

Posted: January 16, 2005 at 12:23 AM / IP Logged

Yes you must have the bitwriter to program remotes as remote 1 and remote 2. Basicly you do your settings, hit write, choose which remote you are using(last remote the alarm saw will always be the default remote shown, if doing settings for all remotes then choose remote 0), then click write again, repeat for additional remotes.

You change remotes by hitting select, I think it is select, if you can't figure it out I will go grab my bitwriter.

Certified Security Specialist

Always check info with a digital multimeter.

I promise to be good.

Tell Darwin I sent you.

I've been sick lately, sorry I won't be on much.

joe435

Member - Posts: 7

Joined: March 15, 2004

Posted: January 16, 2005 at 10:49 AM / IP Logged

Right but how do I change it so driver 1 and driver 2?

jmr964

Copper - Posts: 70

Joined: September 02, 2004

Location: United States

Posted: January 16, 2005 at 11:08 AM / IP Logged

Are you asking in the sense that Driver 1 versus Driver 2 sets the seats, mirrors, etc for the postion of the selected driver?

Jason

joe435

Member - Posts: 7

Joined: March 15, 2004

Posted: January 16, 2005 at 11:11 AM / IP Logged

Right. Do I need to change some wiring or can this be done via the bitwriter? If I do need to change some wiring where do I need to look?

jmr964

Copper - Posts: 70

Joined: September 02, 2004

Location: United States

Posted: January 16, 2005 at 11:17 AM / IP Logged

As far as I know you can not do this. What DEI meant is you can program the alarm remotes individually and control the ALARM/REMOTE START functions differently, not the seats/mirrors/etc.

Jason

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Matrix 3.5 with Bitwriter

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.