2003 GMC Envoy Alarm Wiring Guide
Welcome Guest :)
jpeester
Member -
Posts: 2
Joined: February 24, 2005
Location: United States
Posted: February 24, 2005 at 8:11 PM / IP Logged
Can someone please direct me to a wiring guide for a 2003 GMC Envoy. I am installing an alarm/remote start with a GMDL-BP.
boomer_106
Silver -
Posts: 710
Joined: November 25, 2003
Location: United States
Posted: February 24, 2005 at 8:24 PM / IP Logged
GMC | Envoy / Envoy XL | 2002-2004 |
Remote Starter Wiring Colors and Notes |
Function | | Vehicle Color | Location |
Start: | | YELLOW | IGNITION SWITCH HARNESS * |
Ignition #1: | | PINK | IGNITION SWITCH HARNESS |
Ignition #2: | | WHITE | IGNITION SWITCH HARNESS |
Ignition #3: | | N/A | **** |
Accessory: | | ORANGE | IGNITION SWITCH HARNESS |
Brake Light: | | WHITE | AT SWITCH ABOVE BRAKE PEDAL |
Tach Signal: | | WHITE | IN BLUE PLUG AT THE ECM ON DRIVER'S SIDE OF MOTOR |
Parking Lights: | | BROWN (+) | DRIVER'S KICK PANEL |
Headlights: | | | |
Diesel Glow Plug: | | N/A | |
Clutch Bypass Wire: | | N/A | |
Notes: | | * This Vehicle Is Equipped With GM's PASSLOCK II Anti-Theft System - Use Vehicle Specific Bypass DTI #23545 or Universal Bypass Mpodule. For alternative bypass method see Note #113 , Bypassing Passlock I/II. ** DTI Door Lock Interface #23541 will also disarm alarm. ****All DesignTech remote starters except the 2xx22 have an ignition 3 output - it is the WHITE/ black in the 'control harness.' This wire will be used to control the bypass module, if needed. |
GMC | Envoy / Envoy XL | 2002-2004 |
Alarm and Keyless Entry Wiring Colors and Notes |
Function | | Vehicle Color | Location |
Constant +12 Volts: | | RED | IGNITION SWITCH HARNESS |
OEM Alarm Disarm: | | LT. GREEN (-) | INSIDE OF DRIVER'S DOOR AT MODULE ** |
Dome Lights/Superv: | | GRAY/BLACK (+) | UNDERNEATH DASH AT COURTESY LAMP |
OEM Horn: | | BLACK / YELLOW (-) | STEERING COLUMN HARNESS |
Power Lock: | | SEE NOTE BELOW *** | |
Power Unlock: | | SEE NOTE BELOW *** | |
Trunk Release: | | N/A | |
Alarm Input Wire: | | GRAY/BLACK (+) | UNDERNEATH DASH AT COURTESY LAMP |
Notes: | | ** Module Is Part Of Power Windows/Locks Switch Assembly In Driver's Door. *** Use Vehicle Specific Door Lock Interface #23541. This interface module will also arm/disarm the OEM alarm, elliminating the need to go into the drivers door. As an alternative, one can go Inside Of Driver's, Front Passenger And Rear Hatch To Wire Three Separate 5-Wire Reverse Polarity Systems To The Lock Motors In Each Door. The Wires Are GRAY For Lock And TAN For Unlock. This Will Unlock/Lock The Two Front Doors And The Rear Hatch. The Middle Doors, Must Be Diode Isolated And Wired As A Negative Trigger System Using LT. BLUE For Lock And WHITE For Unlock. The Wires Are Located Under The Rear Seat On The Driver's Side. See Installation Note #201 - Negative Pulse Door Locks And Installation Note #203 - Reverse Polarity Door Lock System. |
jpeester
Member -
Posts: 2
Joined: February 24, 2005
Location: United States
boomer_106
Silver -
Posts: 710
Joined: November 25, 2003
Location: United States
Posted: February 24, 2005 at 10:14 PM / IP Logged
door trigger output is listed as alarm input wire. Gray/Black. Domelight appears to be the same.
Follow the12volt.com
Saturday, September 7, 2024
• Copyright © 1999-2024 the12volt.com, All Rights Reserved
• Privacy Policy & Use of Cookies
Disclaimer:
*All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please
verify all wire colors and diagrams before applying any information.
Topic Closed)
Members
Search
Register
Login
Printable version
