2005 Highlander alarm/remote start wiring

Does anyone have alarm and remote start wiring for a 2005 Toyota Highlander.Thank's Alot

DIRECTWIRE™ WIRING INFORMATION - TOYOTA / HIGHLANDER / 2005 / Remote Start 12volts white (40A), yellow (30A)   +   ignition harness Starter BLACK/ white   +   ignition harness Second Starter black   +   ignition harness Ignition gray   +   ignition harness Second Ignition green   +   ignition harness Third Ignition N/A        Accessory blue   +   ignition harness Second Accessory N/A        Keysense green   -   ign harn or BECU, 2nd plg dwn, pin 2 Notes: Using the status output from the remote start to trigger this wire will disarm the alarm without unlocking the doors. The BECU (Body ECU) is behind the glove box, it is the module to the right. Power Lock see DirectFax document 1070        Notes: The driver side wires are at the driver door module in the door. They are: lock - green in pin 4, unlock - yellow in pin 14, and lock detection - brown in pin 16. The passenger side wires are at the BECU behind the glove box, 2nd plug down from the top. They are: lock - purple in pin 8, unlock - lt. blue in pin 13, and lock detection - brown in pin 11. Power Unlock see power lock notes        Lock Motor blue   5wi BECU, bottom plug, pin 1 Notes: The BECU (Body ECU) is behind the glove box, it is the module to the right. Unlock Motor brown   5wi BECU, bottom plug, pin 2 Notes: The BECU (Body ECU) is behind the glove box, it is the module to the right. Parking Lights+ white to brown   +   driver kick, 20 pin plug, pin 8 Parking Lights- purple   -   switch or BECU, 2nd plug dwn, pin 18 Notes: The BECU (Body ECU) is behind the glove box, it is the module to the right. Hazards orange   -   turn signal flasher left of column Turn Signal(L) red   +   turn signal flasher left of column Turn Signal(R) blue   +   turn signal flasher left of column Reverse Light RED / black to pink   +   driver kick, 14 pin plug, pin 10 Door Trigger see notes   -   BECU behind glovebox, module to R Notes: The driver door trigger is black in the 3rd plug down, pin 11. The front passenger door is lt. blue in the bottom plug, pin 16. The rear door trigger wire is lt. green in the bottom plug, pin 15. Use all three wires and diode isolate each. Dome Supervision green   -   ignition key cylinder illumination Notes: Also found brown (-) at the BECU, bottom plug, pin 11. The BECU (Body ECU) is behind the glove box, it is the module to the right. Trunk/Hatch Pin green   -   BECU, 3rd plug down, pin 6 Notes: The BECU (Body ECU) is behind the glove box, it is the module to the right. Hood Pin GREEN/ black to white   -   pin switch or Theft ECU, pin 34 Notes: The Theft Deterrent ECU is behind the glove box. Trunk/Hatch Release N/A        Power Sliding Door N/A        Factory Alarm Arm arms with lock        Factory Alarm Disarm disarms with unlock        Disarm No Unlock use key sense wire        Tachometer black   ac   ECM, top plug, pin 5 Notes: The ECM (Engine Control Module) is behind the glove box, it is the module to the left. The tach wire is also found at the data link connector, pin 9, under the driver side dash. Wait to start N/A        Brake Wire black   +   brake pedal switch Parking Brake black   -   parking brake switch Horn Trigger pink   -   switch or BECU, bottom plug, pin 10 Notes: The BECU (Body ECU) is behind the glove box, it is the module to the right. Memory Seat 1 N/A        Memory Seat 2 N/A        Memory Seat 3 N/A        Interface Module: Category: Immobilizer Bypass Required: Yes Type: Transponder Part #: 556UW Alternate Part1 #: 555U Notes: Standard on the Limited models, and optional on all other models.        This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter. Directed electronics, Inc. assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information. Be careful whose advice you buy, but be patient with those who supply it.

Thank's alot for the help

You are welcome.Be careful whose advice you buy, but be patient with those who supply it.