96 Jetta Alarm wiring question.

Home / the12volt's Install Bay / Car Security and Convenience / 96 Jetta Alarm wiring question. (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

mrkastro

Member - Posts: 15

Joined: December 01, 2003

Location: United States

Posted: July 12, 2005 at 3:42 PM / IP Logged

hello there. and thanks in advance for your help.

1-) could someone please post a techsheet for the 96 jetta.

2-) I was browsing the forums and someone reported that the parking lights and trunk release have to be isolated by relay. Would you please clarify and tell me how to wire this relay, naming each prong and to where it goes? thank you.

chungo

Copper - Posts: 135

Joined: December 31, 2003

Location: United States

Posted: July 12, 2005 at 5:23 PM / IP Logged

DIRECTWIRE™ WIRING INFORMATION - VOLKSWAGEN / JETTA III / 1996 / Remote Start

[PRINT THIS PAGE]

12volts	red 10 ga.	+	ign. harness - big
Starter	RED / black 10 ga.	+	loop at back of
Second Starter
Ignition	black 16 ga.	+	fuse box
Second Ignition
Notes: There is a positive trigger key sense wire at the ignition switch or in the radio harness. The wire color is BROWN / red.
Third Ignition
Accessory	BLACK / YELLOW 12 ga.	+
Second Accessory
Keysense
Power Lock	yellow/red or gray	+	driver door harness in kick
Power Unlock	RED / blk or green	+	driver door harness in kick
Notes: Requires a double pulse to unlock.
Lock Motor
Unlock Motor
Parking Lights+	gray/red, gray/black		back of lt.switch
Notes: Hidden release tab for light switch on upper left side of switch. Use relays to isolate the switch side of parking light wires from seeing 12v, or the igniton circuit will pulse with the light flash. It is also possible to use the hazard lights. The colors are BLACK/ white and BLACK/ green, and are positive trigger. They can be found at the alarm module or steering column.
Parking Lights-
Hazards
Turn Signal(L)
Turn Signal(R)
Reverse Light
Door Trigger	BROWN / white	-	dr. kick or alarm mod
Notes: The alarm module is located behind the headlight switch.
Dome Supervision
Trunk/Hatch Pin	BROWN / black	-	dr. kick or alarm mod
Notes: The alarm module is located behind the headlight switch.
Hood Pin	BROWN / red	-	behind fuse box
Trunk/Hatch Release	gray		switch
Notes: Gray wire grounded by switch at rest. Use a relay to isolate the switch side of the trunk release wire from seeing 12v.
Power Sliding Door
Factory Alarm Arm	same as lock	+
Factory Alarm Disarm	same as unlock	+
Notes: Use a single pulse to disarm without unlocking.
Disarm No Unlock
Tachometer		AC
Notes: On the 4 cylinder model find a green at the coil on the firewall. The VR6 has a BLACK/ purple at the coil pack. The coil pack is located on the right side of the motor towards the front.
Wait to start
Brake Wire	RED / black	+	brake pedal switch
Parking Brake
Horn Trigger	BLACK / YELLOW	+	behind fuse box
Memory Seat 1
Memory Seat 2
Memory Seat 3

Interface Module:	Category: Immobilizer Bypass	Required: No	Type: N/A
Part #: N/A
Notes:

chungo

Copper - Posts: 135

Joined: December 31, 2003

Location: United States

Posted: July 12, 2005 at 5:31 PM / IP Logged

for the trunk

30 = trunk side

87a = switch side

87 = 12v

86 = 12v

85 = negative trigger from alarm

mrkastro

Member - Posts: 15

Joined: December 01, 2003

Location: United States

Posted: July 12, 2005 at 9:57 PM / IP Logged

so for the parking lights i'm assuming this is the way it goes. please correct me if it is wrong.

1st relay

30 = lights side

87a = switch side

87 = 12v

86 = positive output from alarm

85 = ground

and the same for the second relay. thanks.

chungo

Copper - Posts: 135

Joined: December 31, 2003

Location: United States

Posted: July 13, 2005 at 12:29 PM / IP Logged

that should work

mrkastro

Member - Posts: 15

Joined: December 01, 2003

Location: United States

Posted: July 20, 2005 at 2:32 AM / IP Logged

hello guys.... everything is installed on this car except the TACH WIRE and the HAND BRAKE WIRE that i couldnt find.

please give your 2 cents.

thank you.

Powermyster

Silver - Posts: 962

Joined: April 06, 2005

Location: Ireland

Posted: July 20, 2005 at 7:39 AM / IP Logged

tach- try to find the green at coil(could be different colour) test the tach wire for AC Current it should be between 3-5volts and voltage should rise with revs

is there not a wire on the handbrake assembly for the handbrake wire

mrkastro

Member - Posts: 15

Joined: December 01, 2003

Location: United States

Posted: July 20, 2005 at 2:14 PM / IP Logged

k guys. i went to the CC roadshop today and asked one installer do help me out on this one..... he checked on W/E database they use and the TACH WIRE is BLACK/ Red... i checked the coil and it match with my vehicle....

About the Hand Brake i'm going to research a little better... it should have something on it..... reason is that in the cluster.... there is a BRAKE light wich lights up when i pull the e brake. thanks.

mrkastro

Member - Posts: 15

Joined: December 01, 2003

Location: United States

Posted: July 22, 2005 at 1:06 AM / IP Logged

HAnd Brake wire is BROWN / Yellow at the brake.

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

96 Jetta Alarm wiring question.

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.