2005 Chrysler Pacifica Alarm/Remote Start Wiring

I want to install Car Alarm system, And need some ino about wire colours and location, maybe someone could help me with this. Than you all in advanceCar Audio and car security systems installer. Best in Car audio.

DIRECTWIRE™ WIRING INFORMATION - CHRYSLER / PACIFICA / 2005 / Security 12volts lt. blue/red (10A)   +   ignition harness Notes: This wire is rated at 10 amps only. If installing any system with high current outputs, go to battery for 12V. Starter yellow   +   ignition harness Ignition pink/gray   +   ignition harness Power Lock PURPLE / lt. blue   -   driver door module in door Notes: Lock is negative trigger thru a 1.8K ohm resistor. Unlock is negative trigger thru a 750 ohm resistor. Unlock requires a double pulse. MUST use relays. This wire is not present on the base models which do not have central lock thru the key cylinder on the door. However, a wire can be added to the pin location where the wire would normally be found. It is pin 13, in the 20 pin plug at the driver door module in the door. For reference, the wires next to it are org/tan in pin 12, and lt. blu/wht in pin 14. Power Unlock same as power lock wire        Lock Motor tan/white   5wi driver door module in door Unlock Motor tan/lt. green   5wi driver door module in door Disarm Defeat PURPLE / lt. green   5wi passenger kick, door harness Parking Lights+ use negative wire        Parking Lights- BROWN / white   -   headlight switch or BCM, C5, pin 31 Notes: The parking lights are negative trigger thru a 920 ohm resistor. There is a rest resistance on the wire, so MUST use a relay to isolate away from the switch. The BCM (Body Control Module) is on the driver side firewall under the dash. Hazards WHITE/ dk. blue   -   hazard switch or BCM, C5, pin 1 Notes: The BCM (Body Control Module) is on the driver side firewall under the dash. Turn Signal(L) use hazards wire        Turn Signal(R) use hazards wire        Door Trigger see notes   -   see notes Notes: The driver door trigger is purple at the driver door module in the door. The passenger door trigger is PURPLE / white at the passenger door module in the door. The LR door trigger is PURPLE / gray at the BCM, C2, pin 8. The RR door trigger is purple / YELLOW at the BCM, C3, pin 5. Use all four wires and diode isolate each. The BCM (Body Control Module) is on the driver side firewall under the dash. Dome Supervision yellow/white   -   driver A pillar or BCM, C3, pin 8 Notes: The BCM (Body Control Module) is on the driver side firewall under the dash. Trunk/Hatch Pin PURPLE / orange   -   driver kick or BCM, C3, pin 29 Notes: The BCM (Body Control Module) is on the driver side firewall under the dash. Hood Pin N/A        Trunk/Hatch Release PURPLE / tan   -   driver A pillar or BCM, C3, pin 7 Notes: This wire is for the power liftgate. It is negative trigger thru a 4.7K ohm resistor. MUST use relay. The BCM (Body Control Module) is on the driver side firewall under the dash. Power Sliding Door N/A        Factory Alarm Arm arms with lock        Factory Alarm Disarm disarms with unlock        Disarm No Unlock single pulse power unlock wire        Tachometer NOT BROWN / white   ac   any ignition coil or fuel injector Horn Trigger dk. GREEN/ purple   -   horn switch Memory Seat 1 PURPLE / brown   -   driver door module in door Notes: Memory seat 1 is negative trigger thru an 8K ohm resistor. MUST use relay. Memory Seat 2 same as memory seat 1 wire   -      Notes: Memory seat 2 is negative trigger thru a 2.41K ohm resistor. MUST use relay. Memory Seat 3 N/A   -      Interface Module: Category: Immobilizer Bypass Required: Yes Type: Sentry Key Part #: 556CW Alternate Part1 #: 556UW Alternate Part2 #: 555U Notes: Standard on all models. Interface Module: Category: Door Lock Interface Required: Yes Type: Multiplex Part #: 456LW Notes:        This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter. Directed electronics, Inc. assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information. Be careful whose advice you buy, but be patient with those who supply it.

Thanx for your information. It helped me very much.Car Audio and car security systems installer. Best in Car audio.

I just did this car. I have one problem. When I remote start everything is fine. When I use the Key the windows, heater control and radio do not work. If I disconect the ignition wire everything works again. I am using an audiovox APS-596 two way remote start system. The only thing I can think of is that the remote starter is leaving some voltage on the ignition wire or loading it down. If anyone has any advice I would appreciate it.

Sorry but in our country we dont install remote start systems, because its not popular. GOOD LuckCar Audio and car security systems installer. Best in Car audio.