2004 Chrysler Sebring LX Sedan wiring

I'm looking to install a security system w/ remote start, keyless entry and trunk release. Looking to gain experience with this and help would be greatly apreciated. If you have a wiring diagram or know where I can find one that would be great. Thanks in advance.

DIRECTWIRE™ WIRING INFORMATION - CHRYSLER / SEBRING SEDAN / 2004 / Remote Start 12volts pink/black (40A), red (20A)   +   ignition harness Starter yellow   +   ignition harness Second Starter N/A        Ignition dk. blue   +   ignition harness Second Ignition dk. GREEN/ red (20 AWG)   +   ignition harness Third Ignition N/A        Accessory BLACK/ orange   +   ignition harness Second Accessory BLACK/ white or BLACK/ lt. blue   +   ignition harness Keysense lt. blue   -   ign. harness or BCM, conn. 1, pin 4 Notes: The BCM (Body Control Module) is attached to the fuse/relay box at the end of the dash on the driver side. Connector 1 is a 16 pin plug on the side of the BCM facing the front of the vehicle. Power Lock WHITE/ dk. green   +   BCM, conn. 4, pin 15 Notes: Lock is positive trigger thru a 2.7K ohm resistor. Unlock is positive trigger thru a 620 ohm resistor. MUST use relays. The BCM (Body Control Module) is attached to the fuse/relay box at the end of the dash on the driver side. Connector 4 is a 26 pin plug on the bottom edge of the BCM. Can also use Directed 457C or 456L interface modules. Power Unlock same as power lock wire        Lock Motor ORANGE / black   5wi BCM, conn. 4, pin 9 Notes: The BCM (Body Control Module) is attached to the fuse/relay box at the end of the dash on the driver side. Connector 4 is a 26 pin plug on the bottom edge of the BCM. Unlock Motor dk. blue/white   5wi BCM, conn. 4, pin 13 Notes: The BCM (Body Control Module) is attached to the fuse/relay box at the end of the dash on the driver side. Connector 4 is a 26 pin plug on the bottom edge of the BCM. Parking Lights+ BLACK / YELLOW   +   headlight switch or driver kick Parking Lights- wht/org (NOT on base model)   -   BCM, conn. 1, pin 5 Notes: The BCM (Body Control Module) is attached to the fuse/relay box at the end of the dash on the driver side. Connector 1 is a 16 pin plug on the side of the BCM facing the front of the vehicle. Hazards same as turn signal wires        Turn Signal(L) lt. green   +   turn signal switch Turn Signal(R) tan   +   turn signal switch Reverse Light PURPLE / black or BLACK/ purple   +   driver kick, white 4 pin plug, pin 4 Door Trigger see notes   -   BCM, conn. 4 Notes: The LF door is tan in pin 5, RF door is tan/red in pin 6, LF door is tan/orange in pin 7, and RR door is tan / YELLOW in pin 8. Use all four wires and diode isolate each. The BCM (Body Control Module) is attached to the fuse/relay box at the end of the dash on the driver side. Connector 4 is a 26 pin plug on the bottom edge of the BCM. Dome Supervision yellow   -   front of fuse box, 6 pin plug Trunk/Hatch Pin tan/black   -   BCM, conn. 4, pin 18 Notes: The BCM (Body Control Module) is attached to the fuse/relay box at the end of the dash on the driver side. Connector 4 is a 26 pin plug on the bottom edge of the BCM. Hood Pin N/A        Trunk/Hatch Release BLACK/ white   5wi BCM, conn. 4, pin 1 Notes: The BCM (Body Control Module) is attached to the fuse/relay box at the end of the dash on the driver side. Connector 4 is a 26 pin plug on the bottom edge of the BCM. The trunk release switch wire is BLACK/ white (-) at the switch or at the BCM, conn. 2, pin 3. Power Sliding Door N/A        Factory Alarm Arm lt. GREEN/ orange   +   BCM, conn. 4, pin 4 Notes: Arm is positive trigger thru a 1.8K ohm resistor. Disarm is positive trigger thru a 750 ohm resistor. MUST use relays. The BCM (Body Control Module) is attached to the fuse/relay box at the end of the dash on the driver side. Connector 4 is a 26 pin plug on the bottom edge of the BCM. Can also use Directed 457C or 456L interface modules. Factory Alarm Disarm same as factory alarm arm wire        Disarm No Unlock see factory alarm disarm        Tachometer NOT dk grn/org, dk grn/lt grn   ac   any ignition coil or fuel injector Wait to start N/A        Brake Wire WHITE/ tan   +   brake pedal switch Parking Brake gray/black   -   back of fuse box, blue 10 pin plug Horn Trigger BLACK/ red   -   switch or BCM, conn. 1, pin 2 Notes: The BCM (Body Control Module) is attached to the fuse/relay box at the end of the dash on the driver side. Connector 1 is a 16 pin plug on the side of the BCM facing the front of the vehicle. Memory Seat 1 N/A        Memory Seat 2 N/A        Memory Seat 3 N/A        Interface Module: Category: Immobilizer Bypass Required: Yes Type: Sentry Key Part #: 555CW Alternate Part1 #: 556UW Alternate Part2 #: 555U Notes: Only vehicles with gray keys have the immobilizer. Interface Module: Category: Door Lock Interface Required: Yes Type: Data Bus Part #: 457CW Alternate Part1 #: 456LW Notes:        This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter. Directed electronics, Inc. assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information. Be careful whose advice you buy, but be patient with those who supply it.