Dodge Ram 2003 Remote Start

Home / the12volt's Install Bay / Car Security and Convenience / Dodge Ram 2003 Remote Start (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

SheltonDL

Member - Posts: 5

Joined: July 19, 2005

Posted: August 15, 2005 at 2:38 PM / IP Logged

I am trying to connect an alarm and remote start unit to my truck. I can get the engine to crank remotely, however I cannot get it to start. I have followed the wiring diagrams on here and connected the ignition outputs as directed and still no good. I have checked all the wires going to the ignition to see which ones are energized when the key is turned on, then hooked them in so they would get power when the remote start activates, still no good. I am out of ideas, any thoughts would be appreciated. Also it is a black key truck so that is not the issue.

Thanks,

Velocity Motors

Moderator - Posts: 12,488

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Fabrication. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: August 15, 2005 at 2:59 PM / IP Logged

Is the truck's ignition key grey or black ? If it's gray then you have to use a Sentry bypass module . If it's black, then it's an ignition wire problem.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Search for other posts by Velocity Motors

SheltonDL

Member - Posts: 5

Joined: July 19, 2005

Posted: August 15, 2005 at 6:34 PM / IP Logged

No it does not have a gray key, but rather a black one .

When I use the key to start the truck I hear a ticking from somewhere in the engine compartment and also a buzzing sound which I am asusming is the electric fuel pump. When I use the remote start, I do not get any of the sounds from the engine compartment. So I am assuming that I have missed a wire somewhere, but I cant find it.

Velocity Motors

Moderator - Posts: 12,488

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: August 15, 2005 at 6:42 PM / IP Logged

You should have 2 IGN wire powered up as well as 2 ACC wires powered up. Here they are:

IGNITION|blue (16 awg) |+ |ignition harness

SECOND IGNITION|red or RED / wht |+ |ignition harness

ACCESSORY|green & orange |+ |ignition harness

SECOND ACCESSORY|blue & blk/wht *7 |+ |ignition harness

*7 These wires may not be necessary for remote start.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

dare_ds69

Silver - Posts: 419

Joined: January 25, 2005

Location: New Jersey, United States

Posted: August 15, 2005 at 6:45 PM / IP Logged

12volts	pnk/blk & RED / wht	+	ignition harness
Starter	yellow	+	ignition harness

Ignition	blue (16 awg)	+	ignition harness
Second Ignition	red or RED / wht	+	ignition harness

Accessory	green & orange	+	ignition harness
Second Accessory	blue & blk/wht	+	ignition harness

Tachometer	NOT GREEN/ orange	ac	ign coi, coil pack, or injector
Notes: Diesel tach wire use gray/black in the black plug at the PCM.

Wait to start

see DirectFax document 1091

http://www.directechs.com/techtips/pdfs/resources/security/directed_techtips/1091.pdf

did you use tach, it is a diesel or gas? Dodge Ram 2003 Remote Start -- posted image.

how own your mind, control your life.

MECP certified. always use a DMM

SheltonDL

Member - Posts: 5

Joined: July 19, 2005

Posted: August 15, 2005 at 6:58 PM / IP Logged

I finally found it!!!!

My truck has a green and black wire, not green and orange. 2003 Dodge Ram 2500 Diesel. I guess they ran out of green and orange that day. Anyhow thanks for all the help!!!!

DodgeCrazy

Member - Posts: 4

Joined: June 26, 2004

Location: United States

Posted: September 28, 2005 at 3:49 PM / IP Logged

I am having an issue with my Omega Max remote start/car alarm. I really hope you guys can help.

I recently programmed the echo 2 transciever to the unit following the steps in the instruction manual. The Echo 2 did not work properly because there is something that plugs into the omega unit for the echo 2 to work correctly, which I did not have. I then reprogrammed the original transmitter back to the omega max and since then, my remote start does not work. I can activate the remote start via transciever, the engine will crank run for 3 seconds, then engine kills, and the omega will restsart the engine allowing this process to continue until I terminate the remote start via transceiver. why is it doing this ?? if you need more information please let me know

Thanks

mo12v

Platinum - Nominee - Posts: 2,748

This member consistently provides reliable information

Joined: September 30, 2003

Location: Afghanistan

Posted: September 28, 2005 at 4:08 PM / IP Logged

DodgeCrazy..........

What is Year, Make & Model .....?

You need the ECHO-2 Antenna for the ECHO-2 Transmitter to work

Did you do anything with the wiring??

Don't Learn from Others Mistakes

You Might Be the One That Knows.

DodgeCrazy

Member - Posts: 4

Joined: June 26, 2004

Location: United States

Posted: September 28, 2005 at 4:32 PM / IP Logged

2003 dodge ram 1500 quad cab

no I never touched the wires but could it be possible that a connection has become loose?

Thanks

mo12v

Platinum - Nominee - Posts: 2,748

Joined: September 30, 2003

Location: Afghanistan

Posted: September 28, 2005 at 5:06 PM / IP Logged

If you have a Transponder ByPASS.....U might look at that first

Don't Learn from Others Mistakes

You Might Be the One That Knows.

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.