I tried searching here and other places ( maxima.org ) and I am sure it's something simple that I am just not understanding/reading correctly but I need help with wiring it up.
car - 2000 Nissan Maxima SE automatic ( factory keyless etry/ remote trunk)
remote start unit - Valet 562T w/ 556U by pass
The issues I am confused on I'll highlight in bold
main harness
H1/1 orange = (-) 500mA Armed Output ?optional?
H1/2 white = Parking lights(+) RED / blue location: drivers kick panel
H1/3 WHITE/ blue = ? ?????? activation input??? diagram shows what appears to be a pushbutton momentary switch going to ground.
H1/4 BLACK/ white = ? (dome light) door trigger
option 1 - White (-)location: Right Hand Side of Steering Column ;
option 2 - relay 8616, lt. blue drivers door pin 29, RED / blue pass door pin 40, RED / white rear doors pin 28 SECU, use all 3 and diode isolate each
option 1 is listed here i believe, option 2 came with the starter. Which should I use?
H1/5 n/a
H1/6 blue = ?progressive door unlock ?????can this be used to make it so the lock system works as with the factory remote, one push drivers, two pushes all
H1/7 n/a
H1/8 black = chassis ground connection
H1/9 n/a
H1/10 brown = Horn Trigger: GREEN / WHITE (-) Location: steering column
H1/11 red = 12volts: green (+) Location: ignition harness
H1/12 RED / white = channel 2 output, Trunk Release: blue Location: pin 12 at SECU( 8616 relay)
========================================================
heavy gauge relay satellite wiring
Purple - Starter: BLACK/ red or BLACK/ wht (+) Location: ignition harness, connect to starter side
Green - Starter: BLACK/ red or BLACK/ wht (+) Location: ignition harness, connect to key side
Red(2) - 12V+ ??? Ignition, constant??(high current for relays) there are two wires, connect both or only one?
Orange - Accessory: RED / yellow (+) Location: ignition harness
Pink - Ignition: BLACK/ red (+) Location: ignition harness
Pink/White - Second Accessory: WHITE/ blue (+) Location: ignition harness
RED / White - ???? 12V input connect to additional 12V source, fused is this for an optional add on? or is it supposed to be connected to something?
=================================================
aux harness
H2/1 violet/black = ?? channel 4 output ?? optional? I assume this is for an additional remote controlled output if desired, correct?
H2/2 GREEN / WHITE = Factory Alarm Arm: ORANGE / black (-) Location: pin 41 at SECU ??? relay required??? the install book says to use relays, but there's no mention of them with the supplied diagram, only 2 additional relays wer supplied one for dome supervision/door trigger, and one for trunk release, do I need an additional relay for each output of the factory arm/disarm? also is the vehicle theft system considered the factory alarm, or would this be for an actual alarm with a siren etc?
H2/3 Gray/Black = n/a diesel
H2/4 Light GREEN/ Black = Factory Alarm Disarm:ORANGE / blue (-) Location: pin 30 at SECU ??? relay required???
====================================================
remote start harness
H3/1 Blue/White = rear defrost ?? possible??? what wire? how?
H3/2 Gray = Hood Pin: yellow/red (-) Location: pin 27 at SECU
H3/3 Brown = Brake Wire: RED / green (+) Location: brake switch or drivers kick
H3/4 Violet/White = Tachometer: WHITE/ green Location: instrument cluster or white green wire at ECM
H3/5 BLACK/ White = Neutral Safety Wire GREEN/ Orange (-) Same as Reverse Lights
Supplied on/off toggle switch wired in. Is it required to wire into the neutral safety switch or just run this through the switch to ground?
================================================
door lock ??????????
H4/1 Green = (-) lock (+) unlock
H4/2 n/a
H4/3 Blue = (+) lock (-) unlock
Ok I have 2 problems here.
1 I am not sure what the difference between the lock/unlock motor and power lock/unlock is and which I should be using.
2 Conflicting information. which is right? and can this be used for the progressive unlock?
Power Lock: gray (-) Location: pin 23 at SECU
Power Unlock: BROWN / yel (-) Location: pin 35 at SECU
Lock Motor: purple Location: pin 15 at SECU
Unlock Motor: WHITE/ black Location: pin 13 at SECU
info from [url]www.maxima.org/[/url] supplied with starter [url]www.directechs.com[/url]
Door Lock GREEN/ YELLOW (-) Factory Security Module Right Side of Steering Column
Door Unlock BROWN / Yellow (-) Factory Security Module
Driver's Lock Purple (+) Factory Security Module
Driver's Unlock WHITE/ Black (+) Factory Security Module
Passenger Unlock GREEN/ YELLOW (+) Factory Security Module
info from [url]www.the12volt.com[/url]
================================================
remote start aux harness
1 blue = (-) 200 mA output = status input on 556U by pass
2 orange = (-) 200 mA accessory relay trigger? optional?
3 pink =(-) 200 mA Ignition relay trigger? optional?
4 purple = (-) 200 mA starter relay trigger = connect to relay for second starter wire?
===============================================
===============================================
556U By pass module
Red = 12V +
Blue = (-) status input
Pink = (+) Ignition Input ( not needed?)
Black = Chassis ground ( - )
Violet = (+) Keysense Input (not needed?)
Green = (-) keysense input ( not needed?)