the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

How to re-hook up Clifford Concept40?

Home / the12volt's Install Bay / Car Security and Convenience / How to re-hook up Clifford Concept40? (Topic Closed Topic Closed)
Welcome Guest :)

Post ReplyPost New Topic
< Prev Topic Next Topic >
natenantais 
Member - Posts: 12
Member spacespace
Joined: February 25, 2006
Location: United States
Posted: February 27, 2006 at 2:28 PM / IP Logged  
Ok I just noticed that with the brain out of the car I get no flashing LED near my door lock pin... previously whenever I locked my doors the LED would be flashing.  I guess that means the Concept 40 brain was doing something in there.... so how to make it act like an alarm again?>
mrcllusb 
Copper - Posts: 489
Copper spacespace
Joined: September 06, 2005
Location: Georgia, United States
Posted: February 27, 2006 at 4:51 PM / IP Logged  
If the led was flashing,that means it was working.Try this.Roll down your drivers window.Exit the vehicle and arm the system.Wait about 15 seconds then reach in and unlock your door and open it.If the alarm siren starts going off and the lights start flashing,then it's working ..You can also check and see if you have a shock sensor..
"ole blake"
natenantais 
Member - Posts: 12
Member spacespace
Joined: February 25, 2006
Location: United States
Posted: February 27, 2006 at 5:20 PM / IP Logged  
It's not really working though... the previous owner told me he had it unhooked, and the remotes for the alarm system do nothing.  My car has a stock security system that will honk the horn repeatedly if you open the door from the inside like you described. .  and I believed the LED is original to the car for the stock system, but now doesn't work without the Clifford module hooked up......
mrcllusb 
Copper - Posts: 489
Copper spacespace
Joined: September 06, 2005
Location: Georgia, United States
Posted: February 28, 2006 at 1:44 AM / IP Logged  
I think you need to take your car to a alarm shop near you and have them set it back up.If the previos owner had them unhook it,and can't tell you what they did.The last thing i can think of is that it's in valet mode..This will be the last thing that i can come up with..Try seeing if it's in valet mode..
"ole blake"
natenantais 
Member - Posts: 12
Member spacespace
Joined: February 25, 2006
Location: United States
Posted: February 28, 2006 at 8:16 AM / IP Logged  

How to re-hook up Clifford Concept40? - Page 2 -- posted image. Is it possible it has just been in valet mode for a long time?  If so, how do I get it out?  Do I need the password for the little momentary switch in the dash, or can I get it out of valet mode with the remote?  If I can confirm it's not in valet mode then I'll bring it to a shop.

Thanks a lot for your help...

mrcllusb 
Copper - Posts: 489
Copper spacespace
Joined: September 06, 2005
Location: Georgia, United States
Posted: February 28, 2006 at 8:31 AM / IP Logged  
Do you have a push button,or toggle switch,or do you have the standard 2 black button clifford valet setup?
"ole blake"
mrcllusb 
Copper - Posts: 489
Copper spacespace
Joined: September 06, 2005
Location: Georgia, United States
Posted: February 28, 2006 at 8:36 AM / IP Logged  
You can get out of valet mode by pressing the leveshift button twice,then button 1..If this worked,your parking lights will flash once.The levelshift button is on the rightside of the remote.Button 1 is the main big button.
"ole blake"
natenantais 
Member - Posts: 12
Member spacespace
Joined: February 25, 2006
Location: United States
Posted: February 28, 2006 at 8:38 AM / IP Logged  
I have the switch that is momentary in one direction and toggle in the other... I'll try it with the remote today...
mrcllusb 
Copper - Posts: 489
Copper spacespace
Joined: September 06, 2005
Location: Georgia, United States
Posted: February 28, 2006 at 8:39 AM / IP Logged  
Read my previous post..
"ole blake"
natenantais 
Member - Posts: 12
Member spacespace
Joined: February 25, 2006
Location: United States
Posted: March 06, 2006 at 6:17 PM / IP Logged  

Don't shoot me for thisHow to re-hook up Clifford Concept40? - Page 2 -- posted image., but I just wanted to let you know my alarm works now... the ground cable was unhooked from the battery How to re-hook up Clifford Concept40? - Page 2 -- posted image.... I didn't see the cable until the PO told me he remembered the mechanic unhooking his alarm under the hood.,.. the cable was hanging behind the battery.

Thanks 4 ur help

Page of 2

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Monday, July 14, 2025 • Copyright © 1999-2025 the12volt.com, All Rights Reserved • Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer