the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

92 Caddie Eldorado remote start


Post ReplyPost New Topic
< Prev Topic Next Topic >
Escalade_on20z 
Member - Posts: 24
Member spacespace
Joined: April 02, 2002
Location: United States
Posted: March 25, 2006 at 6:39 PM / IP Logged  
can anyone help me with how to install a remote start into a 92 eldorado? im using a pljx flashlogic by code alarm to bypass the anti theft system. i hooked up my blue wire to the small gauge (non - ) white wire inside the orange sleeve, pink wire to ign,black to cont ground , brown im not sure where to hook this one up at..i followed the insatll manual and hooked it up to a cont ground after i programed the unit. but when i try this set up it does not remote start,i get a signal from my purple starting wire. it will attempt two times then stop, then when i try to start the car it goes into theft mode and does not start for 3mins.?
mo12v 
Platinum - Nominee - Posts: 2,748
Platinum - Nominee spaceThis member consistently provides reliable informationspace
Joined: September 30, 2003
Location: Afghanistan
Posted: March 25, 2006 at 7:26 PM / IP Logged  

The BROWN wire goes to the Remote Start wire that has NEGATIVE Out when Starting & Running

Are you sure the PLJX is Programmed??

MO
Don't Learn from Others Mistakes
You Might Be the One That Knows.
Escalade_on20z 
Member - Posts: 24
Member spacespace
Joined: April 02, 2002
Location: United States
Posted: March 25, 2006 at 9:15 PM / IP Logged  
im pretty sure i have it programed heres what i did i started the car then i pressed the program button until it blinked then i let it go. while doing this i had my black wire hooked up to cont ground and brown disconnected. after i programed it i hooked the brown wire to the alarm black wire (cont ground). is there a BCM on this car, it shows this on the installation guide. do i hook up anything to this? Maybe i just need to do away with this bypass unit and do it with a relay and diode do you have a diagram on how to for this car.
Escalade_on20z 
Member - Posts: 24
Member spacespace
Joined: April 02, 2002
Location: United States
Posted: March 25, 2006 at 9:17 PM / IP Logged  
I meant to say resistor and relay switch .
mo12v 
Platinum - Nominee - Posts: 2,748
Platinum - Nominee spaceThis member consistently provides reliable informationspace
Joined: September 30, 2003
Location: Afghanistan
Posted: March 26, 2006 at 9:30 AM / IP Logged  

Are you sure the Ignition Key has Resistor on shank?

Be sure you have the Jumper accross the last 2 PINS.

Be sure ALL your connections are made PRIOR to Programming, except bROWN wire. ( your Ground should not be removed and reconnected after prograMMING, ETC. )
After you Start the Vehicle with the Key, Press & Hold Program Button....LED will come On solid, then LED will start Blinking.
Then connect Brown wire to R / S Unit.........

Here is VATS install

http://www.wiringinstructions.com/237.htm

Constant 12 voltsREDIGNITION SWITCH HARNESS
Ignition 12 voltsPINKIGNITION SWITCH HARNESS
StarterYELLOWIGNITION SWITCH HARNESS
Ignition #2ORANGEIGNITION SWITCH HARNESS
Ignition #3N/A
AccessoryBROWNIGNITION SWITCH HARNESS

MO
Don't Learn from Others Mistakes
You Might Be the One That Knows.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Saturday, June 8, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer