2006 Chevrolet Aveo alarm wiring

Home / the12volt's Install Bay / Car Security and Convenience / 2006 Chevrolet Aveo alarm wiring (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

manaa

Member - Posts: 14

Joined: April 22, 2006

Location: Algeria

Posted: May 07, 2006 at 8:00 AM / IP Logged

in order to install by my self an alarm système on my car an Chevrolet Aveo 2006 model, i need the electric wiring diagram of this model. i have already the connection diagram of the alarm and i need to now where to connetc all the wires on the car. thank you.

mo12v

Platinum - Nominee - Posts: 2,748

This member consistently provides reliable information

Joined: September 30, 2003

Location: Afghanistan

Posted: May 07, 2006 at 9:40 AM / IP Logged

Constant 12 volts	RED / BLACK & ORANGE	IGNITION SWITCH HARNESS
Ignition 12 volts	PINK	IGNITION SWITCH HARNESS
Starter	YELLOW (smaller gauge)	IGNITION SWITCH HARNESS
Dome Light	ORANGE / BLACK (-)	UNDER DRIVER STEP PLATE
Trunk Pin Switch	ORANGE / BLACK (-)	SAME WIRE AS DOME LIGHT
Parking Lamp	DR. VIOLET (+)	PS. BROWN / WHITE (+) IN DRIVER KICK *
Power Lock	GRAY	IN RCDLR LOCATED **
Power Unlock	YELLOW /GREEN	BELOW REAR OF CENTER CONSOLE **

* Alt. Dome Light- WHITE (-) AT HEADLIGHT SWITCH

** RCDLR- Is Remote Control Door Lock Receiver. If Vehicle is Equipt W/OEM Remote Keyless Entry .... Negative Pulse Doorlocks

If No OEM Keyless, Add An Actuator In The Driver Door.

Accessories
Window Up	D\WHITE P\BROWN D\GREY/GREEN P\VIOLET @ MAIN SWITCH
Window Down	F/D BLUE F/D GREEN R/D GREEN/ RED R/L BLUE
Ign Key Warn	LT GREEN (-)	AT STEERING COLUMN HARNESS
Trunk Release	N/A
OEM Horn	BLACK/ WHITE (-)	AT STEERING COLUMN HARNESS
Headlights	WHITE (-)	AT STEERING COLUMN HARNESS
OEM Alarm Arm	ARMS WITH KEYLESS
OEM Alarm Disarm	BLUE (-)	DRIVER KICK PANEL

Reversal Rest At Ground Power Window

OEM Alarm Horn Wire - DK GREEN / WHITE (-) AT THEFT HORN OEM Alarm Hood Trigger - BROWN / BLACK (+) AT PIN SWITCH

Remote Start
Tach Signal	WHITE	AT DASH TACH,BACK OF CLUSTER *
Ignition #2	RED / BLACK	IGNITION SWITCH HARNESS
Ignition #3	N/A
Accessory	YELLOW	IGNITION SWITCH HARNESS
Neutral Safety	BROWN (-)	BACK OF FUSE BLOCK AT PNP RELAY
Brake Light	BROWN (+)	AT SWITCH ABOVE BRAKE PEDAL
Reverse Light	LT GREEN (+)	AT SWITCH OR REVERSE LAMPS ASSY.
Rear Window Defrost	DK BLUE (+)	AT SWITCH- 20 AMP LATCHING CIRCUIT

Vehicle Immobilizer Bypass

* Tach Wire Also Found As GREY At ECM

Don't Learn from Others Mistakes

You Might Be the One That Knows.

manaa

Member - Posts: 14

Joined: April 22, 2006

Location: Algeria

Posted: May 08, 2006 at 8:44 AM / IP Logged

thank you Mo12v for the informations

manaa

Member - Posts: 14

Joined: April 22, 2006

Location: Algeria

Posted: May 14, 2006 at 3:15 AM / IP Logged

i have finally inderstand all the wiring of my alarm system (thanks to Mo for the wiring diagram he supplied just on this topics) but i have yet a problem with the wiring inside the driver door. on my car i have already a central lock with a switch on the driver side, so i have to add an actuator on this door. th problem: on the door swith there are three (03) wires, on the alarm module there are six (06) wires and the best teh actuator needs seven (07) wires so how to do the correct wiring with this ?would you pleese note that the wirings colors are: orange, white, yellow, orrange/black, WHITE/ black, yellow/black. thanks in advance for every one for any help.

mo12v

Platinum - Nominee - Posts: 2,748

Joined: September 30, 2003

Location: Afghanistan

Posted: May 14, 2006 at 8:48 AM / IP Logged

If your Aveo came WITHOUT Factory keyless Entry, you need to add the Actuator to the Drivers Door to Lock & Unlock the Doors. You would only hook the one Actuator to the Alarm Lock / Unlock Outputs......

Are you trying to hook the Actuator to the Door Switch also??

Don't Learn from Others Mistakes

You Might Be the One That Knows.

manaa

Member - Posts: 14

Joined: April 22, 2006

Location: Algeria

Posted: May 15, 2006 at 8:00 AM / IP Logged

yes my Aveo have no keyless entry. I now that i have to add an actuator on the driver door but I want also to keep the original central lock working (both new system and the old one working in the same time, so I am trying to connet the actuator to the door switch , and i do not now what to do with the six wires coming from the alarm module.

thank you again

mo12v

Platinum - Nominee - Posts: 2,748

Joined: September 30, 2003

Location: Afghanistan

Posted: May 15, 2006 at 8:16 AM / IP Logged

You do not have to connect New Actuator to Door Switch.

You do not reomve old Factory Actuator.

Your Factory Door Locks remain intact.

The added Actuator is just for your Keyless activate door locks

The six wires from Keyless Module is for different wiring configurations i.e.: Negative, Positive, or Reversal.

Post the color & function of wires, also are you using a 2 or 5 wire Actuator?

Don't Learn from Others Mistakes

You Might Be the One That Knows.

manaa

Member - Posts: 14

Joined: April 22, 2006

Location: Algeria

Posted: May 16, 2006 at 4:31 AM / IP Logged

the wires color on the alarm module are:

1. Orange noted : NO 4. ORANGE / black noted : NO1

2. White noted: C 5. WHITE/ black noted: C1

3. yellow noted: NC 6. yellow black noted: NC1

i think the note concernes the internal relay outputs and means:

NO: normaly opened ND: normaly closed C: commun

for the actuator i have a box of four (04) actuators one with 5 wires (i think its for the driver door ) the others are 2 wires. i suppose that i must use the 5 wires one no!

mo12v

Platinum - Nominee - Posts: 2,748

Joined: September 30, 2003

Location: Afghanistan

Posted: May 16, 2006 at 8:41 AM / IP Logged

If the Door Lock Kit DID NOT come with a Relay Module, then use one of the 2 WIRE Actuators and wire like this:

YELLOW = ( N / C ) GROUND

WHITE = ( COM ) ( Lock, Down, or Green Wire?? on Actuator )

ORANGE = 12 Volts Constant ( N / O )

YELLOW/ Black = ( N / C ) GROUND

WHITE / Black = ( COM ) ( UnLock, Up, or Blue Wire?? on Actuator )

ORANGE / Black = 12 Volts Constant ( N / O

Don't Learn from Others Mistakes

You Might Be the One That Knows.

manaa

Member - Posts: 14

Joined: April 22, 2006

Location: Algeria

Posted: May 23, 2006 at 2:44 AM / IP Logged

it works , i have just do the wirings as you explain to me and it works thanks Mo!

it was a great learning experience for me, its the first time i do such a work by my self i found in this forum the help i need, thanks again Mo

now its time to share this learning with others.

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.