1991 buick park avenue

Home / the12volt's Install Bay / Vehicle Wiring Information & File Requests / 1991 buick park avenue (

Topic Closed)

Welcome Guest :)

Members

Search

Register

Login

< Prev Topic Next Topic >

new_beee

Member - Posts: 1

Joined: August 29, 2006

Posted: August 29, 2006 at 5:33 AM / IP Logged

hi, can any one provide me the electrical wiring diagram, colors and position of wires for 1991 buick park avenue, i need it to install my remote key less starter.

thanks

Back to Top

Bmnicolosi

Copper - Posts: 173

Joined: January 26, 2005

Location: Louisiana, United States

Posted: August 29, 2006 at 10:59 PM / IP Logged

DIRECTWIRE™ WIRING INFORMATION - BUICK / PARK AVENUE / 1991 / Remote Start

[PRINT THIS PAGE]

12volts	red	+	ignition harness
Starter	yellow	+	ignition harness
Second Starter
Ignition	pink	+	ignition harness
Second Ignition
Third Ignition
Accessory	orange	+	ignition harness
Second Accessory
Keysense
Power Lock	lt. blue	+	either kick panel
Power Unlock	black	+	either kick panel
Lock Motor	gray		drivers door harness
Unlock Motor	BLACK/ lt. green		drivers door harness
Parking Lights+	brown		low in drivers kick
Notes: Also found at the lighting control module. The lighting control module is located to the left of steering column.
Parking Lights-	dk. blue		light switch
Hazards
Turn Signal(L)
Turn Signal(R)
Reverse Light
Door Trigger	white	-	under dash light
Dome Supervision	use door trigger
Trunk/Hatch Pin	black	-	at switch or light
Notes: Not available on all models.
Hood Pin
Trunk/Hatch Release	lt. blue or blk/wht	+	at release switch
Power Sliding Door
Factory Alarm Arm	yellow	-	drivers door harness
Notes: Not available on all models.
Factory Alarm Disarm	lt. green	-	drivers door harness
Disarm No Unlock
Tachometer	PURPLE / white	AC	ignition module
Notes: May also be found white at the instrument cluster on models with a tachometer.
Wait to start
Brake Wire	lt. blue	+	brake switch
Parking Brake
Horn Trigger	black	-	steering column
Memory Seat 1
Memory Seat 2
Memory Seat 3

Interface Module:	Category: Immobilizer Bypass	Required: Yes	Type: VATS
Part #: 652T resistor pack
Alternate Part1 #: DesignTech 20402
Alternate Part2 #: DesignTech 29402
Notes: See DirectFax document 1049 for interface information.

Smart Starter Kill Relays: Not Available

This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter.

Directed Electronics assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information.

If you say "I already know how", don't ask me a single question.

Back to Top

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

1991 buick park avenue

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.