2006 acura rsx wiring info

Hello I'm looking for the remote start/ alarm wiring info for a 2006 acura rsx not sure if it's the same as the 05? Thank'sJay

DIRECTWIRE™ WIRING INFORMATION - ACURA / RSX / 2006 / Remote Start [PRINT THIS PAGE] 12volts      white (40A)       +       ignition harness Starter      BLACK/ white       +       ignition harness Second Starter      N/A             Ignition      BLACK / YELLOW       +       ignition harness Second Ignition      N/A             Third Ignition      N/A             Accessory      BLACK/ red       +       ignition harness Second Accessory      WHITE/ red       +       ignition harness Keysense      RED / white       -       ign harn or security control unit Notes: The security control unit is to the left of the steering column. Power Lock      WHITE/ blue       -       driver kick, door harness Notes: Also found at the multiplex control unit on the back of the fuse box in a 13 pin plug, pin 12. Power Unlock      WHITE/ green       -       driver kick, door harness Notes: Also found at the multiplex control unit on the back of the fuse box in a 13 pin plug, pin 10. Lock Motor      yellow/black       5wi      driver kick, door harness Unlock Motor      YELLOW /GREEN       5wi      driver kick, door harness Parking Lights+      RED / black or RED / yellow       +       fuse box Parking Lights-      blue       -       switch or security control unit Notes: The security control unit is to the left of the steering column. Hazards      same as turn signal wires             Turn Signal(L)      GREEN/ red       +       turn signal switch Turn Signal(R)      GREEN/ YELLOW       +       turn signal switch Reverse Light      green       +       kick panel, harness to rear Door Trigger      green (D), lt. GREEN/ red (P)       -       security control unit Notes: Use both wires and diode isolate each. The security control unit is to the left of the steering column. Dome Supervision      GREEN/ red       -       driver A pillar Notes: Also found at the rear of the fuse box in a 12 pin plug, pin 7. Trunk/Hatch Pin      red       -       security control unit Notes: The security control unit is to the left of the steering column. Hood Pin      GREEN/ black       -       security control unit Notes: The security control unit is to the left of the steering column. Trunk/Hatch Release      N/A             Power Sliding Door      N/A             Factory Alarm Arm      WHITE/ red       -       security control unit Notes: Meter this wire while turning the key in the driver door key cylinder. The security control unit is to the left of the steering column. May need to use relay in certain applications. Factory Alarm Disarm      white       -       security control unit Notes: Meter this wire while turning the key in the driver door key cylinder. The security control unit is to the left of the steering column. May need to use relay in certain applications. Disarm No Unlock      see factory alarm disarm             Tachometer      blue       ac       ECM/PCM, white 31 pin plug, pin 25 Notes: The ECM/PCM is under the glove box. Also found at the fuse box, top left, 8 pin plug, pin 5. Can also go to any fuel injector and use the wire that is NOT yellow/black. Wait to start      N/A             Brake Wire      WHITE/ black       +       brake pedal switch Parking Brake      GREEN/ orange       -       parking brake switch Horn Trigger      orange       -       horn switch Notes: The horn trigger at the security control unit is green. Memory Seat 1      N/A             Memory Seat 2      N/A             Memory Seat 3      N/A             Interface Module:      Category: Immobilizer Bypass      Required: Yes      Type: Transponder Part #: 556HW Alternate Part1 #: 556UW Alternate Part2 #: DesignTech 20402 Alternate Part3 #: DesignTech 29402 Notes: Standard on all models. When using the 556HW, follow the mode 1 wiring diagram. The reference wire is BROWN / yellow, data wire is RED / blue and ignition wire is BLACK / YELLOW. Smart Starter Kill Relays: Not Available warning       This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter. Directed Electronics assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information. gcorrea

Thank's againJay