99 volvo c70 remote start

Does any one have the wiring info for a remote starter for a 99 volvo c70 convertible? Is it the same as the s70? Thank's in advanceJay

DIRECTWIRE™ WIRING INFORMATION - VOLVO / C70 / 1999 / Remote Start [PRINT THIS PAGE] 12volts      red (10A)       +       ignition harness Notes: This wire is rated at 10 amps only. If installing any system with high current outputs, go to battery for 12v. Starter      yellow/white       +       ignition harness Second Starter                  Ignition      GREEN/ YELLOW       +       ignition harness Second Ignition      blue / YELLOW       +       ignition harness Third Ignition                  Accessory      yellow/purple       5wi      ignition harness Second Accessory                  Keysense      yellow (required)       +       ignition harness Power Lock      yellow/gray       -       keyless module Notes: The keyless module is located above the hood release. It is a black box with 2 green plugs. Power Unlock      gray/red       -       keyless module Notes: Requires a double pulse for unlock. The keyless module is located above the hood release. It is a black box with 2 green plugs. Lock Motor      yellow       5wi      driver kick, door harness Unlock Motor      blue/brown       5wi      driver kick, door harness Parking Lights+      white       +       headlight switch Notes: If you have factory daytime running lights, and you use the white at the switch for parking lights, the headlights will flash as well. The solution is to wire the white at the switch as a 5 wire system. Also, there are 2 white wires at the switch. They go to the same pin. treat them like one wire. Parking Lights-                  Hazards                  Turn Signal(L)                  Turn Signal(R)                  Reverse Light                  Door Trigger      pink/black       -       keyless module Notes: To avoid the dome light delay, there are 2 separate door trigger wires at the keyless module. They are: LF WHITE/ black, RF yellow/brown. Both wires are negative trigger and must be diode isolated from each other. The keyless module is located above the hood release. It is a black box with 2 green plugs. Dome Supervision      comes on with unlock             Trunk/Hatch Pin      blue/brown       -       keyless module Notes: The keyless module is located above the hood release. It is a black box with 2 green plugs. Hood Pin      yellow/black       -       keyless module Notes: The keyless module is located above the hood release. It is a black box with 2 green plugs. Trunk/Hatch Release      yellow/white       -       keyless module Notes: The keyless module is located above the hood release. It is a black box with 2 green plugs. Power Sliding Door                  Factory Alarm Arm      arms with lock             Factory Alarm Disarm      disarms with unlock             Disarm No Unlock      single pulse unlock wire             Tachometer      NOT red, black, or yellow       ac       any ignition coil Wait to start                  Brake Wire      yellow       +       brake pedal switch Parking Brake                  Horn Trigger      yellow/red       -       keyless module Notes: This triggers the alarm horn, the vehicle horns only work with the ignition on. The keyless module is located above the hood release. It is a black box with 2 green plugs. Memory Seat 1                  Memory Seat 2                  Memory Seat 3                  Interface Module:      Category: Immobilizer Bypass      Required: Yes      Type: Transponder Part #: 556UW Alternate Part1 #: DesignTech 20402 Alternate Part2 #: DesignTech 29402 Notes: Smart Starter Kill Relays: Not Available warning       This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter. Directed Electronics assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information. gcorrea

Thank's a lotJay