the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

What Resistor for Dropping 12V to 5V?


Post ReplyPost New Topic
< Prev Topic Next Topic >
Blackiewrx 
Copper - Posts: 56
Copper spacespace
Joined: October 18, 2004
Location: United States
Posted: November 01, 2006 at 2:14 PM / IP Logged  
i need to know how to covert 12v dc to 5 v dc using resistors or somthing? any ideas??
03 wrx stage 4
SoundAudio 
Copper - Posts: 242
Copper spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: May 26, 2004
Location: United States
Posted: November 01, 2006 at 2:35 PM / IP Logged  

Well the values depend on your current draw but a simple voltage divider could be built. PLace two resistors in series with the 2nd resistor value (5/7) of the first resistor value.  Place the resistors between 12v and ground and then you will get 5v at the point between them. This is a very crude way of doing it. It is unregulated so the voltage out will be dependent of voltage in. You will also have to be concerned with power consumption. I believe there was a post earlier with a dedicated part form radio shack that is far better then a resistor voltage divider.

Good Luck!
-Thad
KPierson 
Platinum - Posts: 3,527
Platinum spaceThis member consistently provides reliable informationspace
Joined: April 14, 2005
Location: Ohio, United States
Posted: November 01, 2006 at 3:03 PM / IP Logged  
If you just want a 5vdc output and you will always have at least a 7vdc input use a 7805 from Radioshack.  It will provide up to 1A of current (if used with a heat sink).
Kevin Pierson
i am an idiot 
Platinum - Posts: 13,666
Platinum spaceThis member consistently provides reliable informationspace
Joined: September 21, 2006
Location: Louisiana, United States
Posted: November 01, 2006 at 3:17 PM / IP Logged  

If you are trying to put a 5 volt LED on a 12 volt source   like the others said it is dependent on the current draw,  but you will be safe with a 1K Ohm resistor.

If you are needing it for something other than an LED as KPierson said the 7805 is the way to go and the tab of the 7805 is the ground connection so if you need 1 amp of current  just mount it to the chassis of the vehicle and it will use the car as a heat sink.

If you need several amps of current you can parallel the regulators.  

Blackiewrx 
Copper - Posts: 56
Copper spacespace
Joined: October 18, 2004
Location: United States
Posted: November 02, 2006 at 10:13 AM / IP Logged  
its just for a little portable xm sattlite radio thingy. im sure one amp will be enough. i will look into this radio shack 7805 thing. thanks.
03 wrx stage 4
soultinter 
Copper - Posts: 170
Copper spacespace
Joined: January 16, 2004
Location: United States
Posted: November 02, 2006 at 11:06 AM / IP Logged  
isn't this just like using a resistor to cut the voltage for a ford factory amp turn on?  not sure if it was 1k or 1.5k
KPierson 
Platinum - Posts: 3,527
Platinum spaceThis member consistently provides reliable informationspace
Joined: April 14, 2005
Location: Ohio, United States
Posted: November 02, 2006 at 11:31 AM / IP Logged  

No, it's not the same.  The Ford amp uses a low current input to monitor when it should and shouldn't be on.

The OP is trying to drive a load with a certain voltage.  In a voltage divider circuit the more you load the circuit the more the voltage supplied will drive.  Resistors should only be used to create reference voltages, and should never be used to create a voltage based power supply

Kevin Pierson

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Friday, March 29, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer