the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

how to make switch panel with 12v source


Post ReplyPost New Topic
< Prev Topic Next Topic >
paradice1130 
Member - Posts: 29
Member spacespace
Joined: January 25, 2007
Location: Canada
Posted: April 05, 2007 at 1:49 AM / IP Logged  
Hey guys. I want to make a Switch Panel in the roof console of my truck. Approx 10 - 12 switches. Controlling various things such as rear door poppers, some air valves, and other low amperage accessories. But im trying to figure out a way to run a single 12V source wire up there, how can I do that?
drvnbysound 
Silver - Posts: 289
Silver spacespace
Joined: May 06, 2002
Location: United States
Posted: April 05, 2007 at 6:26 AM / IP Logged  
Check the wiring guide for your vehicle on this website, for a 12V source - will find information on wire color, and location. At that point, its just the task of you running the wire as desired.
Note: I suggest you run an in-line fuse in the wire, preferably close to the 12V source wire you use.
i am an idiot 
Platinum - Posts: 13,581
Platinum spaceThis member consistently provides reliable informationspace
Joined: September 21, 2006
Location: Louisiana, United States
Posted: April 05, 2007 at 5:51 PM / IP Logged  
If we knew what kind of truck you had it would be MUCH easier to help you.
paradice1130 
Member - Posts: 29
Member spacespace
Joined: January 25, 2007
Location: Canada
Posted: April 05, 2007 at 6:02 PM / IP Logged  
Sorry. Its a 1999 Chevy Tahoe. I know where I can find a 12V source and all tha t. But I wanted to run lets say 8 gauge wire from the 12v source, up to my roof console, then somehow distrbiute that to the various switches.
Hymer 
Silver - Posts: 695
Silver spacespace
Joined: November 20, 2004
Location: United States
Posted: April 09, 2007 at 2:09 PM / IP Logged  
I did the same thing in a my 56 chev. Rather than fab a switch panel, I bought a Moroso one. It had all the fuses and such for each ckt. Bassically I ran 00 bat cable from the trunk to a remote disconnect switch , then to the starter solenoid. Off there I ran a 6awg to 100 amp breaker then to a buss bar and then on to the feed lines to my various circuits. [keep in mind the biggest draw is the fuel pump and the lights. really nothing else that draws much current. It works flawlessly. As for hiding things in the roof, run all the wires up the main pillar behind the driver or pass seat, plenty of room.
Tire Proz Stillwater Mn
High End Restyling and Comlete Repair

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 6, 2022 • Copyright © 1999-2022 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer