the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2002 jeep liberty, autopage


Post ReplyPost New Topic
< Prev Topic Next Topic >
tek1001 
Member - Posts: 26
Member spacespace
Joined: January 16, 2006
Location: United States
Posted: September 09, 2007 at 1:45 PM / IP Logged  

Hi hope someone out there can help me out I have a 2002 jeep liberty I installed a autopage alarm remote start with db-chdl4 well it seem to work fine except the rear hatch will not unlock from the autopage remote when the door locks open but if i use the factory keyless entry remote the hatch will open and unlock and today the it only unlocks the door some times and the autopage remote flashs open door when arming and some time it will not arm or disarm any help would be great thank in advance.

tek1001
eurobink 
Copper - Posts: 55
Copper spacespace
Joined: September 06, 2007
Location: Florida, United States
Posted: September 09, 2007 at 6:58 PM / IP Logged  

read what you just wrote... see if you can make out what it says..

then rewrite it so we can understand exactly whats going on and we will help you

tek1001 
Member - Posts: 26
Member spacespace
Joined: January 16, 2006
Location: United States
Posted: September 09, 2007 at 11:34 PM / IP Logged  
well it worked fine except could not get the rear tailgate door to unlock from remote the relay clicks when i push the button on the remote but will not unlock the tailgate and now the doorlocks work fine from the switch but not the remote.they work some times and there are times when they do not work i have gone over the wiring it seems correct.If I use the factory keyless entry remote to unlock the tailgate that works and then i can used the after market remote to unlock the tailgate but it will only work one time then the tailgate will not unlock from the after market remote until i use the factory remote first.I was wondering if it could be a problem with the databus mod i used the db-chdl4 from omega.
tek1001
shaip99 
Copper - Posts: 112
Copper spacespace
Joined: May 04, 2005
Location: Canada
Posted: September 10, 2007 at 6:33 PM / IP Logged  

how did you connect your wires did you use t-taps or did you solder if you used t taps rip the whole thing out and do it again with solder and tape if you used solder and tape pull off all your tape and check for cold solder joints on your connections

by your description is sounds like you have a few bad connection that are intermittantly failing

or another option is that i have completely missunderstood what you were writing cause it made little sence

"Computer games don't affect kids, I mean if Pac Man affected us as kids, we'd
all run around in a darkened room munching pills and listening to repetitive
music."-Kristian Wilson, Nintendo Inc.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Tuesday, October 19, 2021 • Copyright © 1999-2021 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer