2005 Chevrolet Silverado Crew Cab Alarm/Remote Start Wiring

Need a Wiring diagram for a 2005 Chevrolet Silverado Crew Cab

DIRECTWIRE™ WIRING INFORMATION - CHEVROLET / SILVERADO / 2005 / Remote Start 12volts red (40A), red (40A)   +   ignition harness Starter yellow   +   ignition harness Second Starter N/A        Ignition pink   +   ignition harness Second Ignition white   +   ignition harness Notes: To avoid the check engine light from coming on and possible damage to the automatic transmission, the second ignition in this vehicle MUST be powered when adding a remote start system. Third Ignition N/A        Accessory orange   +   ignition harness Second Accessory brown   +   ignition harness Keysense lt. green   -   ignition harness Power Lock use 457G or 456G module        Notes: If Directed module 457G or 456G is not available, refer to DirectFax document 1601. On base model trucks, the 457G or 456G is not necessary. Instead, the lock wire is lt. blue (-), pin B5, and the unlock wire is white (-), pin B10. They are in the lt. blue plug at the BCM. Power Unlock see power lock        Lock Motor gray   5wi driver door module in door Unlock Motor tan   5wi driver door module in door Parking Lights+ brown   +   driver kick panel Parking Lights- gray/black   -   switch or BCM, brown plug, pin B2 Notes: The BCM (Body Control Module) is under the driver side dash. It has 6 plugs in it, the purple plug is on the back. Hazards white   -   hazard switch Turn Signal(L) dk. green   +   turn signal switch Turn Signal(R) lt. green   +   turn signal switch Reverse Light lt. green   +   BCM, black plug, pin F Notes: The BCM (Body Control Module) is under the driver side dash. It has 6 plugs in it, the purple plug is on the back. Door Trigger gray/blk (L), BLACK/ wht (R)   -   each door module in each door Notes: On base model trucks, the door trigger wires are in the lt. blue plug at the BCM, pins B4 and A5. On 4dr trucks, the LR door trigger is lt. blue/black, pin A3, and the RR is lt. GREEN/ black, pin A2. They are in the purple plug at the BCM. Use all wires and diode isolate. The BCM (Body Control Module) is under the driver side dash. It has 6 plugs in it, the purple plug is on the back. Dome Supervision gray/black   +   BCM, black plug, pin E Notes: The BCM (Body Control Module) is under the driver side dash. It has 6 plugs in it, the purple plug is on the back. Trunk/Hatch Pin N/A        Hood Pin N/A        Trunk/Hatch Release N/A        Power Sliding Door N/A        Factory Alarm Arm arms on lock with door open        Factory Alarm Disarm lt. green   -   driver door module in door Disarm No Unlock see factory alarm disarm        Tachometer white   ac   instrument cluster, pin A5 or PCM Notes: The PCM (Powertrain Control Module) is in the left front of the engine compartment to the left of the fan shroud. On gas models, the tach wire is in the green plug, pin 10. On diesel models, the tach wire is in the gray plug, pin 37. On hybrid models, the tach wire is in the green plug, pin 35. For tach can also go to any of the ignition coils or fuel injectors and use the wire that is NOT pink, black, or brown. Wait to start dk. blue   -   instrument cluster, pin A2 or PCM Notes: The PCM (Powertrain Control Module) is in the left front of the engine compartment to the left of the fan shroud. The wait to start wire is in the blue plug, pin 26. Brake Wire white   +   brake pedal switch Parking Brake lt. blue   -   switch or BCM, lt. blu plug, pin A7 Notes: The BCM (Body Control Module) is under the driver side dash. It has 6 plugs in it, the purple plug is on the back. Horn Trigger BLACK / YELLOW to black   -   switch or BCM, gray plug, pin B9 Notes: The BCM (Body Control Module) is under the driver side dash. It has 6 plugs in it, the purple plug is on the back. Memory Seat 1 red   +   driver door module in door Memory Seat 2 pink   +   driver door module in door Memory Seat 3 N/A   +      Interface Module: Category: Immobilizer Bypass Required: Yes Type: Passlock II Part #: 556LW Alternate Part1 #: 555LW Alternate Part2 #: 555T Alternate Part3 #: DesignTech 20402 Alternate Part4 #: DesignTech 29402 Notes: Not required if using the combo interface module. The Passlock II wire colors are yellow, black, and RED / white (not used). Interface Module: Category: Door Lock Interface Required: Yes Type: Data Bus Part #: 456G Notes: Not required if using the combo interface module. Interface Module: Category: Combo Interface Required: Yes Type: Data Bus Part #: 457GW Notes:        This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter. Directed electronics, Inc. assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information. Be careful whose advice you buy, but be patient with those who supply it.