EZ ’glass enclosure question

Home / the12volt's Install Bay / Fiberglass, Fabrication, and Interiors / EZ ’glass enclosure question (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

Xplorer

Copper - Posts: 69

Joined: June 01, 2004

Location: United States

Posted: March 29, 2005 at 2:01 PM / IP Logged

I am making a custom 'glass enclosure for the back of my truck and I have the skeleton made out of MDF and I have the top covered in fleece. I have a rectangle base made of MDF with dowel rods holding the speaker rings floating above the middle of the soon to be enclosure. After I apply the resin to the fleece on the top and layer that up I am wondering if there is a good trick/method to glassing the bottom (obviously needs to be air tight). I plan on putting body filler and painting it if that matters. Thanks.

Peace

realitycheck

Silver - Posts: 751

Joined: September 09, 2004

Posted: March 29, 2005 at 2:10 PM / IP Logged

why dont you make an mdf bottom??? If that is not an optiion because of curves and such I would pull it out and stretch fleece then glass it as well.

Learning the trade one fiberglass creation at a time!

Xplorer

Copper - Posts: 69

Joined: June 01, 2004

Location: United States

Posted: March 29, 2005 at 2:40 PM / IP Logged

I was going to 'glass it because there are metal ribbed looking pieces for a bottom (the floor of my trunk) and i wanted it to fit with those nicely. Should I stretch fleece across the top/places you can see, and staple it to the bottom of the frame, 'glass it for once for strength, then pull fleece across the bottom and staple it to the side so I can hide the staples with layers, then cut out the speaker holes and 'glass the bottom from the inside?

Peace

realitycheck

Silver - Posts: 751

Joined: September 09, 2004

Posted: March 29, 2005 at 3:03 PM / IP Logged

I would take fleece stretch across bottom of frame. Staple to bottom of frame, like the edge of the mdf, that touches the floor. Then I would sit it in the truck how you want it situated. Then I would reach inside and put resin on the fleece from the inside let it cure fully. Then you can pull it out and glass on the inside or the outside of the box. "MAKE SURE" you put down some aluminum foil and tape though before you put resin on the fleece on the bottom. If you dont you probably wont be able to pull the box out ever again.

Learning the trade one fiberglass creation at a time!

Xplorer

Copper - Posts: 69

Joined: June 01, 2004

Location: United States

Posted: March 29, 2005 at 3:58 PM / IP Logged

Alright that sounds like a good idea. Thanks for the input hopefully I'll have some pics next week!

Peace

John64

Member - Posts: 30

Joined: March 25, 2005

Location: United States

Posted: March 29, 2005 at 7:01 PM / IP Logged

Always do the bottom before you glass the top. Aluminum foil works awesome, use the heavy duty kind.

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

EZ ’glass enclosure question

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.