the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

is this strong enough?


Post ReplyPost New Topic
< Prev Topic Next Topic >
Ti240 
Member - Posts: 27
Member spacespace
Joined: January 29, 2005
Location: United States
Posted: September 09, 2005 at 10:47 AM / IP Logged  
a friend is building an enclosure for me and after seeing the finished product i am a little sceptical of its strength. basically the back, sides, top, and bottom are all 3/4 mdf but the face is all fiberglass with a mdf ring "floating" in the center of the glass to mount the sub. the sub is pretty heavy, an eclipse titanium 12", and i was wondering if this is a good way to build a box - just doesn't seem like fiberglass should be used where you would usually find mdf.
2005 Nissan Frontier - stock
comming soon...
Eclipse CD8443 deck
Eclipse PA5422 4-channel
Infinity Kappa Perfect 6.1 front
MBquart DKE116 rear
Eclipse SW9122 the 12's
Eclipse DA7232 bass amp
Poormanq45 
Silver - Posts: 597
Silver spacespace
Joined: October 27, 2004
Location: United States
Posted: September 09, 2005 at 11:02 AM / IP Logged  
Haha, don't be sceptical of fiberglass. If it passed the thumb test it should hold the driver just fine.
What I don't understand is why he used fiberglass on the front only? Usually I prefer an all or nothing approach. Meaning either all MDF, or all fiberglass
Ti240 
Member - Posts: 27
Member spacespace
Joined: January 29, 2005
Location: United States
Posted: September 09, 2005 at 11:06 AM / IP Logged  
well that's good to here, didn't realize that fiberglass could be so strong. thanks for the reply, i swear i learn something here on a daily basis
2005 Nissan Frontier - stock
comming soon...
Eclipse CD8443 deck
Eclipse PA5422 4-channel
Infinity Kappa Perfect 6.1 front
MBquart DKE116 rear
Eclipse SW9122 the 12's
Eclipse DA7232 bass amp
auex 
Platinum - Posts: 5,041
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: December 23, 2002
Location: Arizona, United States
Posted: September 09, 2005 at 5:32 PM / IP Logged  
Poormanq45 wrote:
What I don't understand is why he used fiberglass on the front only? Usually I prefer an all or nothing approach. Meaning either all MDF, or all fiberglass
You would. Note the bold! You don't understand
Fiberglass is stronger then MDF, therefore 1/4" of fiberglass is stronger then 3/4" of mdf. The only difference in strength is when fiberglass is in long flat areas. Fiberglass is strongest in curves.
Certified Security Specialist
Always check info with a digital multimeter.
I promise to be good.
Tell Darwin I sent you.
I've been sick lately, sorry I won't be on much.
haemphyst 
Platinum - Posts: 5,054
Platinum spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spacespace
Joined: January 19, 2003
Location: Michigan, Bouvet Island
Posted: September 09, 2005 at 5:48 PM / IP Logged  
Yes, glass IS stronger than MDF... for FAR less volume occupied, but the strength is not what you should be worried about here... What you SHOULD be worried about is RIGIDITY, something that this thin a layer of glass is NOT going to have. ESPECIALLY if it is a flat surface (I am assuming - sounds that way, as you described it). The rigidity of fiberglass comes from, as auex said, curved surfaces. If that front panel is not curved, it's gonna breathe like a drumskin... VERY MUCH NOT a desired characteristic in a subwoofer enclosure... If it is flat, I can tell you without even looking at it, you need more mass in the panel!
BTW, I am using that SAME woofer, (with the same amplifier) and no matter HOW thick the front panel might be, I would NEVER trust it to hold that driver without some kind of support or MAJOR reinforcement...
It all reminds me of something that Molière once said to Guy de Maupassant at a café in Vienna: "That's nice. You should write it down."
Ti240 
Member - Posts: 27
Member spacespace
Joined: January 29, 2005
Location: United States
Posted: September 10, 2005 at 11:17 AM / IP Logged  
damn...i knew something didn't look right. the front of box is curved though, the mounting ring that the sub screws to sits about 1.5" farther out than the sides of the box. so the fiberglass kinda rolls up from the sides to meet the "ring".
what's the best/easiest way of reinforcing a box like that? one that's already built that is and the only access inside is through the opening where the sub goes. or is it time to start over...
2005 Nissan Frontier - stock
comming soon...
Eclipse CD8443 deck
Eclipse PA5422 4-channel
Infinity Kappa Perfect 6.1 front
MBquart DKE116 rear
Eclipse SW9122 the 12's
Eclipse DA7232 bass amp
Poormanq45 
Silver - Posts: 597
Silver spacespace
Joined: October 27, 2004
Location: United States
Posted: September 10, 2005 at 11:45 AM / IP Logged  
So what you're saying is the front face has a curve to it now. YOu can reinforce it one of two ways; 1: Form the inside, 2: from the outside. Add more 'glass to increase the strength
crzycreations 
Copper - Posts: 52
Copper spacespace
Joined: February 22, 2005
Location: United States
Posted: September 10, 2005 at 12:21 PM / IP Logged  
Have you tried using the enclosure yet?
-Don't buy it, Build it-
Ti240 
Member - Posts: 27
Member spacespace
Joined: January 29, 2005
Location: United States
Posted: September 10, 2005 at 1:14 PM / IP Logged  
no, hasn't been used yet
2005 Nissan Frontier - stock
comming soon...
Eclipse CD8443 deck
Eclipse PA5422 4-channel
Infinity Kappa Perfect 6.1 front
MBquart DKE116 rear
Eclipse SW9122 the 12's
Eclipse DA7232 bass amp
Ti240 
Member - Posts: 27
Member spacespace
Joined: January 29, 2005
Location: United States
Posted: September 10, 2005 at 1:16 PM / IP Logged  
still have to complete wiring and amp rack
2005 Nissan Frontier - stock
comming soon...
Eclipse CD8443 deck
Eclipse PA5422 4-channel
Infinity Kappa Perfect 6.1 front
MBquart DKE116 rear
Eclipse SW9122 the 12's
Eclipse DA7232 bass amp

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer