1999 Mazda Millenia factory alarm

Home / the12volt's Install Bay / Car Security and Convenience / 1999 Mazda Millenia factory alarm (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

quedog

Member - Posts: 2

Joined: June 02, 2004

Location: United States

Posted: June 05, 2004 at 5:00 PM / IP Logged

Need help bypassing factory alarm when using remote start and trunk pop feature. Most info say connect to lt GREEN/ red wire in driver side harness but when I do that the factory alarm still goes off and prevent starting, when I put the key in the door and unlock which bypasses the factory alarm it starts but If i hit the disarm button it kill the car and some funky stuff happen.

I also read to tie into the key sense wire with a positive trigger which didn't really work either but is not a good idea with this car because the key sense wire also makes the steering wheel comes down in this car which is fine when remote starting but every time I hit the unlock button the triggers the steering wheel to move.

Thanks,

Any help is appreciated, Q

jfk51502003

Copper - Posts: 221

Joined: March 04, 2004

Location: United States

Posted: June 05, 2004 at 5:41 PM / IP Logged

DIRECTWIRE™ WIRING INFORMATION - MAZDA / MILLENIA / 1999 / Remote Start

[PRINT THIS PAGE]

12volts	green	+	ignition harness
Notes: Also found in a white plug in a silver box next to the firewall above and behind the fusebox: 12V-WHITE/ red; starter-BLACK / YELLOW 12awg; ignition-BLACK / YELLOW 18awg.
Starter	BLACK / YELLOW	+	ignition harness
Notes: Also found in a white plug in a silver box next to the firewall above and behind the fusebox: 12V-WHITE/ red; starter-BLACK / YELLOW 12awg; ignition-BLACK / YELLOW 18awg.
Second Starter
Ignition	BLACK/ white	+	ignition harness
Notes: Also found in a white plug in a silver box next to the firewall above and behind the fusebox: 12V-WHITE/ red; starter-BLACK / YELLOW 12awg; ignition-BLACK / YELLOW 18awg.
Second Ignition	BLACK/ red	+	ignition harness
Third Ignition
Accessory	blue	+	ignition harness
Second Accessory
Keysense
Power Lock	blu/red or orange		passenger door harness
Power Unlock	same wire		passenger door harness
Lock Motor	red		drivers kick panel
Unlock Motor	blue/black		drivers kick panel
Parking Lights+	orange		drivers kick
Notes: In a large harness to the rear of the car.
Parking Lights-	lt. green or RED / yel		steering column
Hazards
Turn Signal(L)
Turn Signal(R)
Reverse Light
Door Trigger	lt. green	-	drivers kick
Notes: In a large harness to the rear of the car.
Dome Supervision
Trunk/Hatch Pin	red	-	drivers kick
Notes: Rest at ground with the key off. Diode isolate to keep ground from feeding back from the indicator lamp. In a large harness to the rear of the car.
Hood Pin	BROWN / white	-	top of fuse box
Notes: In a 20 pin green plug.
Trunk/Hatch Release	BROWN / white	+	drivers kick
Notes: In the harness coming in from the drivers door.
Power Sliding Door
Factory Alarm Arm	arms with lock
Factory Alarm Disarm	disarms w/ unlock
Disarm No Unlock	lt GREEN/ red or	-	drivers door harness
Notes: Negative trigger through a 1K (1000 ohm) resistor will lock the doors and arm the factory security. Negative trigger on the same wire will unlock all doors and disarm the factory security. Test using the passengers door key cylinder switch with all doors closed. To disarm with out unlocking, send a positive trigger to the blue/black key sense wire. The key sense wire is located at the steering column.
Tachometer	GREEN/ blue		diagnostic connector
Notes: The diagnostic connector is in driver side rear corner of the engine compartment.
Wait to start
Brake Wire	GREEN/ black	+	brake switch
Parking Brake
Horn Trigger	GREEN/ red	-	steering column
Memory Seat 1
Memory Seat 2
Memory Seat 3

Immobilizer Bypass Module:	Required: Yes	Type: Transponder	Part #: 555U
Notes: N/A

1999 Mazda Millenia factory alarm -- posted image.

This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter.

Directed electronics, Inc. assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information.

quedog

Member - Posts: 2

Joined: June 02, 2004

Location: United States

Posted: June 05, 2004 at 8:06 PM / IP Logged

Thank You but I have this info the problem is that when I connect to the lt GREEN/ red wire the factory alarm still goes off and several other problem occur as explained in first post.

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

1999 Mazda Millenia factory alarm

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.