Command Start 2400

Home / the12volt's Install Bay / General Discussion / Command Start 2400 (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

very cold

Member - Posts: 2

Joined: November 29, 2003

Location: Canada

Posted: November 30, 2003 at 12:08 AM / IP Logged

I have a command start 2400 with a CS-306 transmitter.

When the start button is activated, the signal light will blink 9 times, and that's all, nothing else happen's. it was working fine untill now.

Does anyone know's what it means and how to fix it. Check the battery and it's good.

ck auto

Copper - Posts: 257

Joined: September 20, 2003

Location: Canada

Posted: November 30, 2003 at 10:57 AM / IP Logged

hi if i remeber correctly you tach locked diconnect rs power or battery for 15 seconds reconnect and should be good to go they were quirky that way

good luck

kirk

very cold

Member - Posts: 2

Joined: November 29, 2003

Location: Canada

Posted: November 30, 2003 at 8:12 PM / IP Logged

Thank you kirk. I did what you said and it work. It was -30c this morning.

Thanks again.

Ed.

racmar

Member - Posts: 1

Joined: November 30, 2003

Location: Canada

Posted: November 30, 2003 at 8:58 PM / IP Logged

I just happened to be searching for info on my CS2400 as I was having the same problem. Lucky for me I came accross this bb. Command Start is out of business and there is not much out there. Needless to say, I followed your advice and my unit works perfectly now. I just hope I do not loose the remote as I do not where I would find one.

Once again, Thanks

racmar

Velocity Motors

Moderator - Posts: 12,488

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Fabrication. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: December 01, 2003 at 10:56 AM / IP Logged

Command Start did not go out of business, they went into receivership and the company as a whole is not together, but yo can still get new and warranty parts for it. The warranty is being done through a shop in Winnipeg, Manitoba and the distribution is still being done through major distributors out East and in Central Canada.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Search for other posts by Velocity Motors

bestbuy_1

Member - Posts: 1

Joined: December 03, 2003

Location: Canada

Posted: December 03, 2003 at 1:07 PM / IP Logged

I registered just to post this reply. Thanks for the info on the Command Start CS2400. Mine started giving the exact same symptoms around the end of November. Outside temp was no more than -10C, but I got the same 9 flashes of the Turnsignal lights. Disconnecting the Battery(s) for over 15 seconds did the trick. Thanks for the info. I will spend some time browsing this site to see what else I can learn.

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Command Start 2400

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.