the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

A few questions, installing tomorrow


Post ReplyPost New Topic
< Prev Topic Next Topic >
bignissan 
Member - Posts: 10
Member spacespace
Joined: November 17, 2004
Location: United States
Posted: November 26, 2004 at 8:15 PM / IP Logged  
I'm installing my Inifinity Kappy 100.3SE tomorrow, along with the Kenwood 608-S 300 watt amp. My questions are: What guage speaker wire should I run inside the box from the terminal to the sub? I'm assuming the same guage from the amp to the terminal. The stuff that came in my wiring kit seems small.
Also, I have a brandnew BOSS c-150 amp, RMS power is 40x2. Would you recommend running the 4 component speakers off that or just off my head unit? My head unit is a Kenwood 40x4, but with a 22 watt RMS. My components are Pioneer 6 1/2 2-ways in my doors, and Pioneer 6x8 3-way in the rear cab section. All this is in a 1995 Ford F-250 regular cab.
Did I leave anything out?? Anything else you need to know? Thanks for the help!!!
Greg
bignissan 
Member - Posts: 10
Member spacespace
Joined: November 17, 2004
Location: United States
Posted: November 26, 2004 at 8:16 PM / IP Logged  
Also, if I run the two amps, I already have the wire junction and everything for it. 4 guage wire from the battery, then a junction with two 8 guage wires exiting.
uthinkuknoaudio 
Silver - Posts: 760
Silver spacespace
Joined: October 08, 2004
Location: United States
Posted: November 26, 2004 at 8:24 PM / IP Logged  
Well, the boss amp will not give you the sufficient power, as they are overated distorted amps. I never recommend running comps off of the hu, as it can cause problems/electrical failures and damage it. I would run 12 guage wire running from your amp to your block, to your subs. That is all you really nead, as Infinity's are really not that power hungry in which you might need to bump up to an 8 guage. So in this case, 12 should be fine. When installing all of this, remember to remove the fuse from under your hood, as you might blow it when moving or plugging in the terminal on your amplifier. Trust me i found out the hard way (Like 19 fuses and counting)... Keep your ground cable short as always, and make sure you have a clean connection on everything. Use good quality RCA's, not the stuff from RadioShack. Some people might say RCA's are RCA's, but really you can tell the difference dramitically if you get a nice pair. Personal recommendation: Monster Cable. It has never treated me bad, and i've never had to replace a pair. Good luck!
"I don't play games. I play Nakamichi and that for real yo" - Probably some japanese kid said this in the early 80's trying to sell stereo out of his trunk lol.
bignissan 
Member - Posts: 10
Member spacespace
Joined: November 17, 2004
Location: United States
Posted: November 26, 2004 at 8:30 PM / IP Logged  
thanks for the advice. I've installed a few systems before...and actually my room mate left the fuse in last week when we were installing his amp and blew a few radio fuses.
He's running the same BOSS amp that I have powering 2 10's...they sound amazingly decent the cheap little amp...not sure how long it will last, but it's sounds decent. Would it be worth hooking up the BOSS that I have for the components since I already have it? Or just leave it off the head unit? They sound ok now...at least to me, but since I have the amp, if it's worth giving it a shot, I might at well use it.
The RCA's I have came in the SCOSCHE wiring kit I got.
bignissan 
Member - Posts: 10
Member spacespace
Joined: November 17, 2004
Location: United States
Posted: November 26, 2004 at 8:37 PM / IP Logged  
edit: just re-read the post, the boss will not give sufficient power for the components? Maybe I'll just try selling it and picking up a cheap 4 channel...
stevdart 
Platinum - Posts: 5,816
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spaceThis member consistently provides reliable informationspace
Joined: January 24, 2004
Location: Pennsylvania, United States
Posted: November 26, 2004 at 8:49 PM / IP Logged  
You can run the fronts with the boss amp, and the rears off the head unit.  You want them lower in volume than the fronts, anyway.  4 gauge splitting to 8 gauge will give you plenty of beef for future upgrades, so that is a good idea.  Speaker wire doesn't have to be so beefy, as the power from an amplifier is higher voltage/lower amperes...that is, don't compare speaker wire to power wire.  16 gauge is plenty big enough for your needs, 14 ga. won't make any difference.  There's just not that much amps running through the wire.  The Scoshe RCA's will be fine.
uthinkuknoaudio 
Silver - Posts: 760
Silver spacespace
Joined: October 08, 2004
Location: United States
Posted: November 26, 2004 at 8:50 PM / IP Logged  
Well, i really don't see the boss amp helping you out. You might get like 20W out of it if your lucky, that is 20 Clean watts. I'd sell it and grab an inexpensive amp like a JBL or an alpine. They are pretty darn cheap on ebay, see what you can find.
"I don't play games. I play Nakamichi and that for real yo" - Probably some japanese kid said this in the early 80's trying to sell stereo out of his trunk lol.
audiobass10 
Silver - Posts: 328
Silver spacespace
Joined: October 11, 2004
Location: United States
Posted: November 27, 2004 at 6:51 AM / IP Logged  

I think anything over 14awg would be an over kill with the power you're running...i ran 14 awg with 800wrms..14 awg will be sufficient for most applications..i think anything 1000wrms and over id think about 12awg..other than that you're fine. If you do get a new amp..check out the JBL 180.2 on www.sounddomain.com ...i'm pretty sure they have some more refurbs for cheap on there.

Dave
Pioneer Premier DEH-P660
15" Kicker CVR
Profile AP1000M
It's Loud
audiobass10 
Silver - Posts: 328
Silver spacespace
Joined: October 11, 2004
Location: United States
Posted: November 27, 2004 at 6:54 AM / IP Logged  
haha..maybe jbl doesn't make a 180.2..i thought they did...if they do its not on the site anymore.
Dave
Pioneer Premier DEH-P660
15" Kicker CVR
Profile AP1000M
It's Loud
bignissan 
Member - Posts: 10
Member spacespace
Joined: November 17, 2004
Location: United States
Posted: November 27, 2004 at 10:02 AM / IP Logged  
thanks for the help. I'm going to run the wires for another amp, and just not hook up the boss right now. I've been looking on ebay and there are some good deals for some kenwood and pioneer amps.
Page of 2

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer