the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

14.4 Volts


Post ReplyPost New Topic
< Prev Topic Next Topic >
TheSaint421 
Copper - Posts: 137
Copper spacespace
Joined: July 07, 2004
Location: Canada
Posted: December 10, 2004 at 3:38 AM / IP Logged  

Getting 14.4 volts to your audio system... whats the best way to accomplish this.

The Saint

wheelerdr 
Copper - Posts: 337
Copper spacespace
Joined: October 25, 2004
Location: Louisiana, United States
Posted: December 10, 2004 at 3:46 AM / IP Logged  
start out with at least 2 guage wire from you batterywith a 150 amp fuse as close to the battery as possible. from here tun it to you amp and a 2 guage ground from your amp to the closest grounding point, not a seat bolt or anything to the bare metal, and from that it depends on what kind of system how many watts. what size alt do you have  are you running multi amps or just one.
TheSaint421 
Copper - Posts: 137
Copper spacespace
Joined: July 07, 2004
Location: Canada
Posted: December 10, 2004 at 4:13 AM / IP Logged  

one Alpine MRD 1001 puts out 1000W @ 2 hom @ 14.4 volts, connected to 3 Alpine Type - X 10" subs

I have 0 guage wire running from the battery, and a 0 guage ground wire thats about 1.5 Ft long connected to bare metal in the trunk. anything else I can do ?

Thanks, The Saint

crispycritter91 
Member - Posts: 15
Member spacespace
Joined: January 22, 2004
Location: United States
Posted: December 10, 2004 at 5:18 AM / IP Logged  
Have you thought about upgrading the ground wire that goes from the battery to the engine/body of the vehicle. The manufacture typically uses the bare minimum wire for that (8~4 Gauge). It is pretty much used to power all the items that were installed from the manufacture. You can actually gain a lot of things from upgrading. More MPG, HP, brighter Headlights, better response from your audio and video, etc... There are also aftermarket kits for this application that I cannot remember the name right now but it does show improvement in the electrical realm...
TheSaint421 
Copper - Posts: 137
Copper spacespace
Joined: July 07, 2004
Location: Canada
Posted: December 10, 2004 at 5:26 AM / IP Logged  

damn, I never thought of using a grounding kit... that would probably do the trick.. thanks

The Saint

crispycritter91 
Member - Posts: 15
Member spacespace
Joined: January 22, 2004
Location: United States
Posted: December 10, 2004 at 6:50 AM / IP Logged  
No prob. Another thing to try is upgrading the ALT. It cost an arm and a leg but trust me. It helps. Try http://www.mechman.com/home.html He modifies Mopar Alts to any vehicle Foreign and Domestic.... I order one from him a few years back. Very professional, nice, and is willing to help you. His alt are HOT rated not cold rated. I had a Ford 165amp Hot (220amp COLD)   Alt with (2) 0 GA neoprine covered cables, the adapter for the electrical adapter, and an adapter to fit the ALT in a 1987 Mistu Montero. Took me about 30 minutes to install. I think I paid about 6 or 700 for it. Got it with in 2 weeks and the awesome thing is the cables actually have pellets of coper instead of the typical strans... Means its more flexable. Speaking of the ALT. I trashed the Montero and left the alt exposed to the elements for almost 2 years. Covered with rust. I took it to advance auto and they tested... Still runs like new! To bad I never though of ordering another set of adapters for my Nissan Frontier... so I gave it to a friend... Oh well. Good luck!
crispycritter91 
Member - Posts: 15
Member spacespace
Joined: January 22, 2004
Location: United States
Posted: December 10, 2004 at 7:06 AM / IP Logged  

Well heres more on your grounding wire situtation. Try here for that aftermark kit http://store.racinglab.com/hygrsybysun.html Or if you really want to go cheap, get the gauge wire you would like to used. Since your using 0Ga try using that or  00Ga to compesate for other electrical Items. Just get how much you think you'll need, and some crimps. Take off one wire at a time and cut the new wire to length. Make sure you do have some slack in the line to prevent catosrophic damage due to vibration. Put the crimps on... (Highly recommed that you solder them down as well!!!) Less resistance and less chances of vibrating loose and possible lose of power to your rig. Cheers!


Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer