the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

amp noise and grounding issue


Post ReplyPost New Topic
< Prev Topic Next Topic >
pendulum 
Copper - Posts: 56
Copper spacespace
Joined: January 02, 2006
Location: United States
Posted: June 28, 2007 at 10:09 PM / IP Logged  
I finally got around to fixing my ground, since I upgraded to 4GA last night, and it didn't make any difference. My new ground is a 1/4 inch stainless steel bolt, with a star washer on one side, a "Keps" nut (standard hex nut with star washer integrated), then a star washer, my ground eyelet, another star washer, and a nylon lock nut. all paint is ground off to metal using an air grinder on the inside, and i got as much as I could get off on the outside. The bolt is coming from the wheel well to behind my rear seat. I still get a noise if I turn my gain   to about 2v which is where it should be, and I still get a POP when I turn the key off. btw- I put a small amount of solder on the ground eyelet. Not too much.
In the pic, you cant see the bottom side of the ground but all of the paint is ground down with an air grinder...Amp is a lightning strike s4.500.1, 4 GA pwr/gnd, Stinger RCA's on opp side of vehicle, all terminals are tight. Problems existed with 8 gauge wire and old RCA's as well.
1999 Toyota Camry
--
Pioneer DEH-P3700MP
Lightning Audio Strike S4.15.VC2
Lightning Audio Strike S4.500.1
Majestic 6.5"
pendulum 
Copper - Posts: 56
Copper spacespace
Joined: January 02, 2006
Location: United States
Posted: June 28, 2007 at 10:13 PM / IP Logged  
Here's a link to the pic
GROUND STUD
1999 Toyota Camry
--
Pioneer DEH-P3700MP
Lightning Audio Strike S4.15.VC2
Lightning Audio Strike S4.500.1
Majestic 6.5"
jmelton86 
Gold - Posts: 1,228
Gold spacespace
Joined: February 07, 2007
Location: South Carolina, United States
Posted: June 28, 2007 at 11:49 PM / IP Logged  

The problem lies in your HU. Pioneers are well known for noise through the RCA outs.

Ground out all the negative contacts on your RCA wires(the outer ones, thank God!), preferably at the HU side. Your problem will cease to exist.

2013 Kia Rio -90a alternator
DDX470HD GTO14001 GTO1014D (x3)
Big3 in 1/0G
1/0G to GTO14001
hamzter 
Copper - Posts: 116
Copper spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: March 15, 2005
Location: United States
Posted: June 28, 2007 at 11:51 PM / IP Logged  
will this work for Eclipse Radios also?
Mark "Hamzter" Cinense
1991 Infiniti G20 w/JDM SR20DE
Eclipse CD8445
MTX Thunder 684
Polk DB6750
Polk DB6500
Optima Red Top in the Trunk
jmelton86 
Gold - Posts: 1,228
Gold spacespace
Joined: February 07, 2007
Location: South Carolina, United States
Posted: June 29, 2007 at 1:27 AM / IP Logged  
Not to my knowledge which is, I must say, limited. I do remember reading in a previous post of yours about this. Someone told you that Eclipse HU's can be defective, too. I doubt this is your problem, but you can always try. While your system is on, touch a grounded wire to your RCA negatives, the outer ones. If the noise goes away, that's your problem. If not, your HU can be defective.
2013 Kia Rio -90a alternator
DDX470HD GTO14001 GTO1014D (x3)
Big3 in 1/0G
1/0G to GTO14001
pendulum 
Copper - Posts: 56
Copper spacespace
Joined: January 02, 2006
Location: United States
Posted: June 29, 2007 at 1:34 AM / IP Logged  
Will this also take care of my popping noise when I turn the key off? That's the most annoying thing out of all...
1999 Toyota Camry
--
Pioneer DEH-P3700MP
Lightning Audio Strike S4.15.VC2
Lightning Audio Strike S4.500.1
Majestic 6.5"
jmelton86 
Gold - Posts: 1,228
Gold spacespace
Joined: February 07, 2007
Location: South Carolina, United States
Posted: June 29, 2007 at 1:41 AM / IP Logged  

Are you using the remote turn-on wire to power up the amp or one tapped into an acc wire? If the amp stays on when the HU cuts off then that's when it makes the noise. Likewise if the amp is on when the HU is turn on then the pop noise will occur. Try turning off the amp before the HU.

2013 Kia Rio -90a alternator
DDX470HD GTO14001 GTO1014D (x3)
Big3 in 1/0G
1/0G to GTO14001
Steven Kephart 
Platinum - Posts: 1,737
Platinum spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spaceThis member consistently provides reliable informationspace
Joined: November 06, 2003
Location: Oregon, United States
Posted: June 29, 2007 at 2:58 AM / IP Logged  

1st of all, what kind of noise are you getting?  Is it alternator wine?  Does it change in volume when you turn up the volume on the radio?  I've seen in the past that there are some ground locations that will produce noise in a system no matter how good a ground you create.  The solution in those instances was to move the ground to a different location.  But it's important to make sure the noise isn't coming from something else. 

Most quality amplifiers include circuitry that eliminates turn-on and turn-off pops.  If your amp doesn't include that circuitry, then I believe Peripheral makes an outboard circuit you can add to your system that will fix the problem. 

pendulum 
Copper - Posts: 56
Copper spacespace
Joined: January 02, 2006
Location: United States
Posted: June 29, 2007 at 3:46 AM / IP Logged  
It's kind of like a static, I guess. Just sound. Not alt. whine. And, two different amps have done it, with 2 completely different wiring kits. the only constant variable is my remote wire, which is run straight from the HU Remote wire.
1999 Toyota Camry
--
Pioneer DEH-P3700MP
Lightning Audio Strike S4.15.VC2
Lightning Audio Strike S4.500.1
Majestic 6.5"
hamzter 
Copper - Posts: 116
Copper spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: March 15, 2005
Location: United States
Posted: June 29, 2007 at 6:22 AM / IP Logged  
pendulum wrote:
It's kind of like a static, I guess. Just sound. Not alt. whine. And, two different amps have done it, with 2 completely different wiring kits. the only constant variable is my remote wire, which is run straight from the HU Remote wire.
Have you tried adjusting the gains on your amp(s)?
I suppose my HU could be an issue as my noise is alternator noise, but the noise appears and then disappears.
sometimes it is there and sometimes it goes away... So I am wondering if it is the HU.
Mark "Hamzter" Cinense
1991 Infiniti G20 w/JDM SR20DE
Eclipse CD8445
MTX Thunder 684
Polk DB6750
Polk DB6500
Optima Red Top in the Trunk
Page of 2

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer