viper 5901 in 2002 nissan frontier

im installing a viper 5901 in my lil bro's 2002 Nissan Frontier 4dr. and everything was going coo as far as searching and finding wires and all and realized his truck has the factory keyless or alarm watever it is so all in all would i need to hook up the oem alarm arm/disarm outputs from the h2, 18pin harness...and for the main harness (H1) on the wire colors for the door trigger input its says that its RED / black on for h1/8 pin but then as for the h1/9 pin (-) 200ma dome light supervision output its saying the same color as well do i tie the two together?

I am not sure what you are asking, so here is what I think you are looking for. If you are grabbing the RED / black at the A pillar, it is the wire that supplies the light with ground to turn on. You would need to use a relay for dome light supervision, the BLACK/ white only provides 200ma of output. Pin 87 ground Pin 30 RED / black in truck Pin 86 constant fused +12V Pin 85 H1/9 BLACK/ white The green H1/8 would also get tied to the RED / black. This is what tells the alarm the door is open. If the truck is equipped with dome delay (most are) you would need to turn off the door trigger error chirp (2-4) as well.Installer, IT support, and FFL. I need less hobbies.

ok so use like a 610t relay for that ok well what i was asking was i see on the h2 harness theres an oem alarm disarm output and oem alarm arm output and i was wondering if those hook up to the oem keyless/alarm thats currently in the frontier and i would need to connect any other of the wires in the h2 harness and i think i got the h/3 harness figured out..

Yes you would want to tie in the OEM arm and disarm (GREEN/ black and GREEN / WHITE) to control the factory alarm with your new system. The other wires in the H2 would be for trunk release/accessory activation/etc so they are not mandatory connections. And...the horn honk output as well if you want (not really needed if you are using the included siren).Installer, IT support, and FFL. I need less hobbies.

ok coo so now the question is which wires on the frontier side would be the oem arm/disarm wires?

Yellow/Red is Arm Yellow is Disarm Both are at the smart entrance module to the left of the steering column.Installer, IT support, and FFL. I need less hobbies.

so here we go for the remote start h3/1 pink    +ign 1 input/output h3/2 RED / wht (87)flex relay input (30a) h3/3 orange +accessory output h3/4 violet +starter output(carside of starter kill) h3/5 green   +starter input (keyside of starter kill) h3/6 red     ignition 1 input(30a) h3/7 pnk/wht (30) flex relay output h3/8 pnk/blk (87a)flex relay input h3/9 RED / blk accessory/starter relay input (30) vehicle colors are batt.    green ign 1    blk/wht ign 2    RED / yellow acc.1    wht/blue startr1 blk / YELLOW startr2 grn / YELLOW keysense wht/grn so theres no keysense wire watsover ign.1 blk/wht wire goes to h3/1 pink ?             wire goes to h3/2 RED / wht acc wht/blue wire goes to h3/3 org carside blk / YELLOW wire goes to h3/4 purple keyside blk / YELLOW wire goes to h3/5 green ign1 blk/wht wire goes to h3/6 red ?             wire goes to h3/7 pink/wht ?             wire goes to h3/8 pink/blk ?             wire goes to h3/9 RED / blk

coo thanks for the help most appreciated...

bump... someone know the ?'s blanks? am i on right track?

bump.... stuck would like to get this finished for him... i've read that i need to hook up both starter wires but how? do i cut both starter wires and hook up the violet to car side and the other two to green (keyside)?