2004 suburban, remote/security, 5901

Home / the12volt's Install Bay / Car Security and Convenience / 2004 suburban, remote/security, 5901 (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

calhounautocare

Member - Posts: 4

Joined: January 24, 2011

Location: West Virginia, United States

Posted: January 24, 2011 at 10:15 AM / IP Logged

I have a 2004 Chevy Suburban in which I'm installing a Viper 5901 along with the XK09. My install is mostly complete except for the H3 harness with only the H3/1 pink hooked to the vehicle RED / white strip. My remaining power/accessory wires on vehicle are red, brown, orange and white. Does anyone know exactly which H3 harness wires to hook to the vehicle colors/wires? I also got the 508D and am wondering about an install location. Lastly, the XK09 hooks up via D2D cable only, right? From what I understand XK09 is powered through the D2D? Thanks

Search for other posts by calhounautocare

monty_77

Copper - Posts: 491

This member has made a donation to the12volt.com. Click here for more info.

Joined: January 15, 2009

Location: North Dakota, United States

Posted: January 24, 2011 at 11:28 AM / IP Logged

h3 harness

pink ignition 1 to Pink of ignition harness

Pink/white ignition 2 to white of ignition harness (if not hooked up you risk transmission damage)

Orange accessory one to Orange of ignition harness

Pink/black not used

Violet yellow at ignition harness Vehicle side of starter wire if you want anti-grind or starter kill(if nether are wanted don't cut start wire and hook this up)

Green yellow at ignition harness key side of starter wire if you want anti-grind or starter kill(if nether are wanted don't cut start wire and don't hook this up)

Red, RED / white, and RED / black need to be attached to a 12v sources two red wires at the ignition harness should work good.

you will also have to add a relay to handle the second accessory brown.

pin 87 and 86 to 12v 30 amp fused

pin 87a not used

pin 30 to Brown second accessory at ignition harness

pin 85 to Relay output Orange RS accessory (-) 200mA output

The XK09 can be hardwired to

if you do not use the d2d cable you then hook up all the blue color dash wires in the manual

monty_77

Copper - Posts: 491

Joined: January 15, 2009

Location: North Dakota, United States

Posted: January 24, 2011 at 11:42 AM / IP Logged

on a second note you will have to hard wire the door pins for the rear doors and hatch at the BCM to the trigger wires.

they are not detected through bus system.

also that RED / white you attached to i bet its a 12 volt source and not the ignition

you will want to check all wires with a digital multi meter

calhounautocare

Member - Posts: 4

Joined: January 24, 2011

Location: West Virginia, United States

Posted: January 24, 2011 at 2:29 PM / IP Logged

Thanks for the replies. So I understand to use relay on the brown vehicle wire, and control it with the H3/3 orange, but you stated above that for the H3/3 orange to go to accessory 1 orange of ignition harness? By the way, the vehicle red and RED / white are constant power, or source. From what I gathered from your 2nd reply is the H3/1 pink needs to be on a switched circuit. As far as I remember the vehicle pink is switched power. Is this where you still want the H3/1 pink? Also, any ideas on location of 508D? Thanks again!

monty_77

Copper - Posts: 491

Joined: January 15, 2009

Location: North Dakota, United States

Posted: January 24, 2011 at 2:37 PM / IP Logged

monty_77 wrote:

pink ignition 1 to Pink of ignition harness

pin 85 to Relay output Orange RS accessory (-) 200mA output

the wire i said is a negative output off the relay output of the Remote starter

also know as the Remote start auxiliary output in the installation manual

calhounautocare

Member - Posts: 4

Joined: January 24, 2011

Location: West Virginia, United States

Posted: January 25, 2011 at 10:19 AM / IP Logged

Thanks in advance to anyone thats familiar and can help with Viper/XK09 install in a 2004 Suburban. I have had several vehicle diagrams offered which I'm familiar with. I'm having trouble w/ conn. pin descriptions of H3. I am hoping to find help from experienced person with this particular install. Here is my pinout of H3: H3/1 Pink (+)Ignition 1 Input/Output; H3/2 RED / White (+)Fused (30A) Ignition 2/ Flex Relay Input 87; H3/3 Orange (+)Accessory Output; H3/4 Violet (+)Starter Output (Car side of starter kill); H3/5 Green (+)Starter input (Key side of the starter kill wire); H3/6 Red (+)Fused (30A) Ignition 1 Input; H3/7 Pink/White (+) Ignition 2/ Flex Relay Output; H3/8 Pink/Black (+)Flex relay input 87A key side (if required) of Flex relay; H3/9 RED / Black (+)Fused (30A) Accessory/Starter Input; H3/10 NC (no connection) My vehicle ignition harness wires are: Red, RED / White, Yellow, Pink, White, Orange, Brown. Does anyone know this particular combo to hook to which. Please don't recommend a vehicle/or 5901 wiring diagram, I already have both. In my business, I sometimes have to help people with specific repair instructions such as tightening seq. & torque specs. Thanks again

monty_77

Copper - Posts: 491

Joined: January 15, 2009

Location: North Dakota, United States

Posted: January 25, 2011 at 11:18 AM / IP Logged

if you look at my first post you will see all your answers

""pink ignition one to pink of ignition harness""

monty_77

Copper - Posts: 491

Joined: January 15, 2009

Location: North Dakota, United States

Posted: January 25, 2011 at 11:24 AM / IP Logged

i will relabel to make it easier for you

h3 harness vehicle wire

pink ignition 1 to Pink of ignition harness

Pink/white ignition 2 to white of ignition harness (if not hooked up you risk transmission damage)

Orange accessory one to Orange of ignition harness

Pink/black not used

Violet yellow at ignition harness Vehicle side of starter wire if you want anti-grind or starter kill(if nether are wanted don't cut start wire and hook this up)

Green yellow at ignition harness key side of starter wire if you want anti-grind or starter kill(if nether are wanted don't cut start wire and don't hook this up)

Red, RED / white, and RED / black need to be attached to a 12v sources two red wires at the ignition harness should work good.

you will also have to add a relay to handle the second accessory brown.

pin 87 and 86 to 12v 30 amp fused

pin 87a not used

pin 30 to Brown second accessory at ignition harness

pin 85 to Relay output Orange RS accessory (-) 200mA output

relay output is located by the H2 harness and Valet program switch

The XK09 can be hardwired to

if you do not use the d2d cable you then hook up all the blue color dash wires in the manual

smokeman1

Platinum - Posts: 1,589

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: September 14, 2009

Location: Wisconsin, United States

Posted: January 25, 2011 at 12:15 PM / IP Logged

Monty_77 is giving you the wiring guidence you are asking for. You must use a DMM to verify the wires you are about to connect to.

Take it one wire at a time test, verify, and solder.

When all else fails, Read the Instructions

Support the12volt.com Make a Donation

calhounautocare

Member - Posts: 4

Joined: January 24, 2011

Location: West Virginia, United States

Posted: January 25, 2011 at 2:50 PM / IP Logged

Thank you. The only relay output orange RS accessory by the H2 harness and valet program switch that I can come even close to would be H2/12 which is IN the H2 connector and is descripted as orange (-)200Ma Accessory ouput. Location of a 508D a sore subject? Thanks again. Your help is greatly appreciated. Bear with me, install mostly complete. I'll repost results

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.