the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

JDL-PK on a 1999 Jeep Gr Cherokee


Post ReplyPost New Topic
< Prev Topic Next Topic >
abright52 
Copper - Posts: 137
Copper spacespace
Joined: September 25, 2002
Location: United States
Posted: November 23, 2003 at 11:51 PM / IP Logged  
I am installing a Crimestopper RS 900 IV on a 1999 Jeep Grand Cherokee Limited with the OEM Alarm.
I have the JDK-PK Bypass.
We have everything hooked up, and the doorlocks will lock, but they will not unlock. When you press either button, lock or unlock, there is a slight delay and then it locks, but it sends the lock signal twice, one about 4-5 seconds after the other.
We also cannot get the vehicle to start. The ignition wires all power up as if you put the key in the "On" position, and there is power going out to the starter from the RS system, but no start.
Install Guide for RS 900 IV
Install Guide for JDL-PK
Here is how everything is hooked up:
Module - Jeep
Connector 1:
Brown - Yellow (Starter)
Gray - RED / Blk (Acc)
Red - Red (+ Constant)
Red - Pnk/Blk (+ Constant)
Pink - Dk Blue (Ign)
Pnk/Whi - Blk/Org (Ign 2)
Connector 2:
White (-) - Brown of JDL-PK
Yel/Whi - Gry/Org (Horn)
Blk - Ground
Yel/Blk - Not Used (- IGN)
Tan - Not Used (Aux)
Green - Not Used (Start Activate)
Gray - Hood
Pink - Not Used (Glow Plug)
Purple - Whi/Tan (Brake)
Org/Blk - Lt Grn/Org (OEM Alarm Disarm)
Orange - Not Used
RED / Whi - Not Used (Tachless)
Connector 3 (Locks):
Blue - Blue of JDL-PK (Unlock)
Red - Not Used (+ for relays)
Green - Green of JDL-PK (Lock)
JDL-PK:
Brown - White of RS900IV (- Output When Running)
Green - Green of RS900IV (Lock)
Blue - Blue of RS900IV (Unlock)
Vio/Whi - Not Used (Unlock Priority)
Violet - Yel/Vio (Pin 2 of Data Port)
Pnk/Whi - Not Used
Pink - Not Used
Orange - Not Used (Panic)
Red - Red of RS900IV (+ Constant)
Black - Black of RS900IV (Ground)
I did not use any relays, I don't think I needed any unless I missed something.
Also, for the "Negative Ground Output When Running" from the JDL-PK I used the Parking Light Output from the RS900IV, will that suffice?
Any ideas on the door locks and the starting?
securinu 
Silver - Posts: 772
Silver spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: September 15, 2002
Location: United States
Posted: November 24, 2003 at 10:59 PM / IP Logged  
might be as simple as a bad module have you tried swapping it out????
Joe O'Byrne
Owner / Installer
abright52 
Copper - Posts: 137
Copper spacespace
Joined: September 25, 2002
Location: United States
Posted: November 24, 2003 at 11:05 PM / IP Logged  
I only have one module.
securinu 
Silver - Posts: 772
Silver spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: September 15, 2002
Location: United States
Posted: November 24, 2003 at 11:11 PM / IP Logged  
check your - out i dont think that will work   pk lights flash  and so the signal will be interupted
Joe O'Byrne
Owner / Installer
securinu 
Silver - Posts: 772
Silver spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: September 15, 2002
Location: United States
Posted: November 24, 2003 at 11:14 PM / IP Logged  
try the yellow /black - ignition out
Joe O'Byrne
Owner / Installer
abright52 
Copper - Posts: 137
Copper spacespace
Joined: September 25, 2002
Location: United States
Posted: November 24, 2003 at 11:16 PM / IP Logged  
That was the next thing I was going to try. I think I will hook it up to the Yel/Blk wire that is supposed to power an extra (-) IGN.
I never thought about the Pk Lights flashing, on my RS they are on constant when you push the start button, this one may be different, or not enough current.
Thanks.
EDIT: Thanks for the suggestion on the YEL/BLK, I wrote this before seeing your post. I guess we were on the same wavelength.JDL-PK on a 1999 Jeep Gr Cherokee -- posted image.
abright52 
Copper - Posts: 137
Copper spacespace
Joined: September 25, 2002
Location: United States
Posted: December 21, 2003 at 12:07 AM / IP Logged  
Just as an update, I switched it over to the YEL/BLK wire. Works flawlessly now.
Thanks!
wiretapper 
Copper - Posts: 166
Copper spacespace
Joined: December 11, 2003
Location: United States
Posted: December 22, 2003 at 9:34 AM / IP Logged  
albright, Yel/Blk is the wire you you every time for that. That's what it's there for.  Transponer bypasses, anti-grind, or anything that needs to be on with the remote start.
abright52 
Copper - Posts: 137
Copper spacespace
Joined: September 25, 2002
Location: United States
Posted: December 22, 2003 at 11:07 AM / IP Logged  
Yeah, I know that now. I was helping out a friend on the Jeep and I hadn't fully read the directions as to what that wire actually does. After I took the time to read it, it was pretty clear that I needed to use that wire.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer