Impulse Imp 1010

Home / the12volt's Install Bay / Car Security and Convenience / Impulse Imp 1010 (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

Harry

Member - Posts: 20

Joined: March 28, 2002

Location: United States

Posted: April 06, 2002 at 7:00 PM / IP Logged

Hi, I just got a Impulse imp 1010 alarm from e Bay, and didn't get any instructions with it. does anyone know of any sites that would have them. I E- mailed the seller, but I wanted to install it on Sunday or Monday. It has the wire color code on the back of the alarm, but I wanted something a little more detailed.

Thanks Harry, Havertown, Pa

the12volt

Administrator - Posts: 3,957

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: March 07, 2002

Location: Louisiana, United States

Posted: April 06, 2002 at 7:59 PM / IP Logged

Hi Harry, post what's listed on the back of the unit here and we can give you detailed information.

the12volt

Harry

Member - Posts: 20

Joined: March 28, 2002

Location: United States

Posted: April 06, 2002 at 8:44 PM / IP Logged

This is on the back of the Alarm:

Red...... +12 volt main power

white..... Parking Light +12V (10 amps)

Brown..... Siren output +12V

Blue/White..... Door lock out(-)

WHITE/ Red...... Door unlock out(-)

Orange..... (-) Negative Armed Output

BROWN / White...... Horn Out(-)

BLACK/ White..... Dome light

Blue..... Negative Trigger for Sensors

Gray..... Trunk Release out(-)

Yellow .......Switched +12Volt Acc. input

Black .....System ground

Violet..... Door Triger Postive

Green..... Door Triger Negative

The alarm also has plug in L.E.D. , Push button switch and a shock sensor.

I'm installing this in a 1996 Chevy Cavalier Z24 with electric door locks

Thanks Harry

Velocity Motors

Moderator - Posts: 12,488

This member has been recognized as an authority in Fabrication. Click here for more info.

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: April 06, 2002 at 9:42 PM / IP Logged

I scanned in the wiring diagram for the IMP 1010 for you and you can view it here :

http://www.velocitymotorsport.com/IMP_1010.jpg

The wiring diagram for the 1996 Cavalier Z24 is here:

https://www.the12volt.com/installbay/detail.asp?info=alarm&year=1995-96&make=Chevrolet&model=Cavalier&ID=17399&type=Alarm

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Search for other posts by Velocity Motors

the12volt

Administrator - Posts: 3,957

Joined: March 07, 2002

Location: Louisiana, United States

Posted: April 06, 2002 at 9:50 PM / IP Logged

Hi Harry, here's wire for wire on your vehicle and alarm:

Red...... +12 volt main power

Connect this lead to the positive terminal of the battery (fused)

white..... Parking Light +12V (10 amps)

Connect this lead to terminal #85 of an SPDT relay, connect #87 to 12V+ (fused), connect #86 to ground, connect #30 to Brown parking lamp wire loacted in the driver's kick panel. ( Brown wire should show 12V+ only when parking lamps are on)

Brown..... Siren output +12V

Connect to positive side of siren, ground the other lead fo the siren.

Blue/White..... Door lock out(-)

Connect to terminal #85 of an SPDT relay. Locate and cut the Light Blue door lock wire in the driver's side kick panel and connect the switch side of it to terminal #87a, connect #30 to the motor side of the lead you just cut, connect #86 and #87 to 12V+.

WHITE/ Red...... Door unlock out(-)

Connect to terminal #85 of an SPDT relay. Locate and cut the White door unlock wire in the driver's side kick panel and connect the switch side of it to terminal #87a, connect #30 to the motor side of the lead you just cut, connect #86 and #87 to 12V+.

Orange..... (-) Negative Armed Output

Connect to an optional starter kill relay as shown here: https://www.the12volt.com/relays/page2.asp#sk1

BROWN / White...... Horn Out(-)

Connect to the Black wire in the steering column harness that shows ground when you honk the horn and shows 12V+ at rest.

BLACK/ White..... Dome light

Connect as shown here: https://www.the12volt.com/relays/page4.asp#ien

Blue..... Negative Trigger for Sensors

Connect to any sensor negative output. If more than one is used, diode isolate each output.

Gray..... Trunk Release out(-)

Connect to terminal #85 of an SPDT relay. Connect #30 to the BLACK/ White wire located at the factory keyless entry module in the trunk, connect #86 and #87 to 12V+.

Yellow .......Switched +12Volt Acc. input

Connect to the Pink wire in the ignition switch harness. This lead will onlyt show 12V+ when the key is in the start and run positions.

Black .....System ground

Connect to the vehicle's chassis.

Violet..... Door Triger Postive

Not used in your vehicle.

Green..... Door Triger Negative

Connect to your illuminated entry relay ( https://www.the12volt.com/relays/page4.asp#ien )and to the White wire at the coutesy lamp under dash.

Other info on your vehicle: https://www.the12volt.com/installbay/detail.asp?info=alarm&year=1995-96&make=Chevrolet&model=Cavalier&ID=17399&type=Alarm

If you need anything else, let us know.

the12volt

Harry

Member - Posts: 20

Joined: March 28, 2002

Location: United States

Posted: April 06, 2002 at 10:18 PM / IP Logged

Thanks for your help!!!!!! You guys are GREAT!

Harry

the12volt

Administrator - Posts: 3,957

Joined: March 07, 2002

Location: Louisiana, United States

Posted: April 06, 2002 at 10:22 PM / IP Logged

You're welcome Harry, glad we could help.

Harry

Member - Posts: 20

Joined: March 28, 2002

Location: United States

Posted: April 21, 2002 at 2:46 PM / IP Logged

I finally got aroud to trying to install this alarm, but....... I don't quite under stand what I'm doing with the "Green...door triger Negative" I got the part about the BLACK/ White.(Domelight) and the relay, but what do I do with the "Green" wire? What do I hook up to what?

Thanks Harry

Velocity Motors

Moderator - Posts: 12,488

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: April 21, 2002 at 5:17 PM / IP Logged

Find the door pin wire that activates the dome light when the door is opened. Splice into this wire and if the wire registers a ( - ) then hook this wire up to the GREEN wire of the IMP 1010 . If the door pin wire registers ( + ) when the door is open then you hook up the VIOLET wire. Most GM's are negative trigger so you won't need the VIOLET wire.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Impulse Imp 1010

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.